ASRock RX 6900 XT OC Formula 16GB GPU Water Block with Backplate – Bykski A-AR6900XTOCF-X

Bykski · A-AR6900XTOCF-X

Full-cover water block for the ASRock RX 6900 XT OC Formula

The Bykski A-AR6900XTOCF-X is a full-cover GPU water block for the ASRock Radeon RX 6900 XT OC Formula 16GB. It replaces the stock air cooler and transfers heat from the GPU core, graphics memory, and voltage regulators to a custom liquid-cooling loop. This version includes a black aluminum backplate and 5V addressable lighting.

Fits
ASRock RX 6900 XT OC Formula 16GB
Coverage
GPU core, memory, and VRM
Port thread
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Match the OC Formula board layout.

  • ✓ASRock Radeon RX 6900 XT OC Formula 16GB (RX6900XT OCF 16G)

Before ordering, confirm the full model number and compare your card’s PCB with Bykski’s reference layout.

ASRock Radeon RX 6900 XT OC Formula 16GB with its stock cooler.

Design Highlights

Manufacturer’s coolant-flow illustration.

Cooling across the board

The cold plate spans the GPU die, memory, and voltage regulators. Coolant flows through the block and carries their heat to the radiator.

Jet microchannels in the copper plate

The cold plate uses a jet microchannel design with 0.5 mm gaps.

5V addressable lighting

For motherboard control, use the included adapter cable between the light strip and a 5V 3-pin ARGB header. A compatible Bykski 5V RBW controller can also run the strip.

Key Specifications

ModelA-AR6900XTOCF-X
Cold plateT2 copper
TopClear acrylic
BackplateBlack aluminum, mounted behind the PCB
Cooling coverageGPU core, graphics memory, and VRM
Port threadG1/4 inlet and outlet
Water block (L × H × T)264.59 × 152.28 × 23.28 mm
Lighting5V 3-pin ARGB (RBW)

Manufacturer drawing. Dimensions in millimeters.

Which Version Do I Need?

Use the series name and PCB to choose between these two Bykski blocks.

A-AR6900XTOCF-XTHIS PAGE
Choose this block for the ASRock RX 6900 XT OC Formula 16GB after verifying the OC Formula PCB layout.
Choose this block for the ASRock RX 6900 XT Phantom Gaming D 16G OC or RX 6900 XT Taichi X 16G OC. Check the exact card model on the product page and compare your PCB with Bykski’s reference layout before ordering.

What's in the Box

1 × full-cover GPU water block1 × black backplate2 × G1/4 stop plugs1 × mounting hardware set1 × thermal pad set1 × 5V ARGB light strip5V 3-pin motherboard ARGB adapter cable

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Water block and backplate.

Installation & Use

1
Shut down the PC, remove the graphics card, and take off the stock cooler.
2
Clean the GPU die and remove the old thermal pads. Check that the PCB and block mounting holes line up.
3
Apply the supplied pads to the specified memory and VRM contact points. Apply your own thermal paste to the GPU die.
4
Align the block, PCB, and backplate. Secure them with the supplied mounting hardware, tightening the screws evenly.
5
Connect the loop with G1/4 fittings and seal the unused ports with the stop plugs. For the lighting, use the included adapter cable to connect the strip to a 5V 3-pin motherboard ARGB header, or connect the strip to a compatible Bykski 5V RBW controller.
6
Fill the loop and check for leaks with only the pump powered. Keep the graphics card and the rest of the PC off during the test.

You also need a pump, reservoir, radiator, G1/4 fittings sized for your tubing, tubing, and coolant.

1 Water block · 2 Thermal pads · 3 Graphics card PCB · 4 Washers · 5 Spring screws · 6 Backplate · 7 Backplate screws

FAQ

How do I check whether this RX 6900 XT block fits my card?

Check for ASRock’s RX6900XT OCF 16G model number and match the PCB to Bykski’s reference layout.

Are thermal pads included, and where do they go?

A thermal pad set is included. Position the pads at the memory and voltage-regulator contact points specified in the installation guide for your mounting kit.

Which fittings do I need?

Use G1/4 fittings at the block and choose fittings that match your tubing size.

Can I connect the lighting to a 12V RGB header?

The block’s lighting requires a 5V 3-pin ARGB connection. A 12V 4-pin RGB header can damage it.

Notes
  • This is a repair or replace only item. Returns not accepted on compatibility issues or if block has had water/fluid run through it.
  • Manufacturer reserves right to alter block design to expand compatibility. Delivered item may not 100% match pictured item.
  • Not responsible for any damage caused by or when using this product. Please use at your own risk.