Bykski · N-AS3070TITUF-X
Full-cover water block for ASUS TUF Gaming RTX 3060 Ti and RTX 3070 Ti
The Bykski N-AS3070TITUF-X replaces the stock cooler on compatible ASUS TUF Gaming cards. Its copper cold plate cools the GPU, memory, and voltage regulators. G1/4 ports connect the block to a custom liquid cooling loop, and the included aluminum backplate mounts behind the card.
Fits
ASUS TUF Gaming RTX 3060 Ti O8G / RTX 3070 Ti 8G
Compatibility
Bykski lists these two ASUS TUF Gaming PCB layouts.
- ✓ASUS TUF Gaming RTX 3070 Ti 8GB (TUF-RTX3070TI-8G-GAMING)
- ✓ASUS TUF Gaming RTX 3060 Ti OC 8GB (TUF-RTX3060TI-O8G-GAMING)
Before ordering, check the full model code on your card and verify its PCB layout.
ASUS product photo of the TUF-RTX3070TI-8G-GAMING.
Design Highlights
Bykski schematic of coolant flow through the block.
One cold plate for the GPU, memory, and VRM
The full-cover plate picks up heat from the GPU die, memory modules, and voltage regulators. Coolant carries that heat into the loop.
0.3 mm jet microchannels
Coolant passes through narrow channels in the T2 copper plate. The clear acrylic top shows the flow path.
5V addressable lighting
The RBW light strip illuminates the clear top. Use a compatible 5V ARGB controller or connect to a 5V 3-pin motherboard header with a matching sync cable.
Key Specifications
| Model | N-AS3070TITUF-X |
|---|
| Cold plate | T2 copper |
|---|
| Top | Clear acrylic |
|---|
| Backplate | Black aluminum, outside the coolant path |
|---|
| Port thread | G1/4 |
|---|
| Microchannel gap | 0.3 mm |
|---|
| Block width | 147.55 mm, including the terminal |
|---|
| Backplate (L × W × T) | 239.85 × 117.55 × 6.00 mm |
|---|
| Lighting | 5V 3-pin ARGB (Bykski RBW) |
|---|
Bykski backplate drawing. Dimensions in millimeters.
What's in the Box
1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × 5V ARGB light stripThermal padsMounting hardware set
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
1Power off the system, remove the graphics card, and take off the stock cooler. Clean off the old thermal materials and check the block’s mounting holes against the PCB.
2Cut the thermal pads to fit the memory and VRM contact areas shown by Bykski. Apply a thin layer of your own thermal paste to the GPU die.
3Align the block, card, and backplate. Place the washers and tighten the spring screws around the GPU gradually in a diagonal pattern. Fit the backplate screws in the remaining positions.
4Connect the G1/4 fittings to the ports marked IN and OUT, then seal the unused ports with the stop plugs. Leak-test the loop before powering the card.
For the loop, have G1/4 tubing fittings, matching tubing, a pump, a radiator, and coolant on hand.
① water block · ② thermal pads · ③ your graphics card PCB · ④ washers · ⑤ spring screws · ⑥ backplate · ⑦ backplate screws.
FAQ
Which ASUS TUF RTX 3060 Ti does this block fit?
Bykski lists the TUF-RTX3060TI-O8G-GAMING. Verify the complete model code and PCB before ordering.
Which ASUS TUF RTX 3070 Ti does it fit?
Bykski lists the TUF-RTX3070TI-8G-GAMING. Check the PCB layout as well as the model code.
Which fittings do I need?
Use G1/4 tubing fittings that match your tubing. The two included G1/4 stop plugs seal the unused ports.
Can I connect the lighting to a 12V RGB header?
Connect to a 5V 3-pin ARGB header with a matching sync cable, or use a compatible 5V ARGB controller. A 12V RGB header can damage the light strip.
Notes- This is a repair or replace only item. Returns not accepted on compatibility issues or if block has had water/fluid run through it.
- Manufacturer reserves right to alter block design to expand compatibility. Delivered item may not 100% match pictured item. Product does NOT come with English instructions. Please see product gallery images for install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points with the exception of the GPU core, which uses thermal paste. Installing pads on other components can lead to improper contact and poor performance.
- Not responsible for any damage caused by or when using this product. Please use at your own risk.