Bykski · C-ML370X8-X
Full-cover water block for the Cambricon MLU370-X8
The Bykski C-ML370X8-X is a full-cover water block with a backplate for the Cambricon MLU370-X8 48 GB PCIe accelerator. It replaces the card’s passive heatsink with a nickel-plated copper cold plate that contacts the accelerator chips, memory, and power circuitry. A custom liquid cooling loop carries that heat to a radiator.
Fits
Cambricon MLU370-X8 48 GB PCIe
Cold plate
Nickel-plated T2 copper
Compatibility
Bykski lists this board layout.
- ✓Cambricon MLU370-X8 48 GB (PCIe 4.0 ×16, ML370X8 PCB layout)
Before ordering, match your exact card model, PCB layout, and mounting holes to the board in the photo.
Cambricon MLU370-X8 bare PCB shown by Bykski.
Design Highlights
Full-cover T2 copper cold plate
The 264 mm cold plate spans the accelerator chips, memory, and power circuitry. Bykski lists a thermal conductivity of 401 W/(m·K) for the copper itself.
Manufacturer’s coolant path illustration.
Coolant path across both accelerator chips
Coolant flows through two microchannel areas in the cold plate. The black POM terminal provides the G1/4 inlet and outlet for your loop.
Key Specifications
| Model (SKU) | C-ML370X8-X |
|---|
| Cold plate | Nickel-plated T2 copper |
|---|
| Cover and terminal | Stainless steel cover and black POM terminal |
|---|
| Backplate | Black anodized aluminum |
|---|
| Port thread | G1/4 |
|---|
| Water block (L × W × T) | 277.86 × 106.49 × 32.08 mm |
|---|
| Backplate (L × W × T) | 266.78 × 106.65 × 6.00 mm |
|---|
| Lighting | None |
|---|
Manufacturer drawing in millimeters. Water block above, backplate below.
Which Version Do I Need?
Look for the full MLU370-X8 model name. Cambricon lists the MLU370-X4 as a 24 GB single-slot card and the MLU370-S8 as a 48 GB half-height, half-length card.
Bykski C-ML370X8-XTHIS PAGE
Choose this block if your MLU370-X8 matches the pictured PCB and you plan to use a custom loop.
What's in the Box
1 × full-cover water block1 × aluminum backplate5 × 1.5 mm thermal pad strips8 × 0.5 mm insulating washers8 × M2 × 5 mm spring screws7 × M2 × 9.5 mm backplate screws
Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.
1 Water block · 2 Thermal pads · 3 Your PCB · 4 Insulating washers · 5 Spring screws · 6 Backplate · 7 Backplate screws
Installation & Use
1Shut down the system, remove the card, and take off its stock heatsink.
2Clean off the old thermal materials and check that the block lines up with the card’s mounting holes.
3Cut the 1.5 mm thermal pad strips to fit the memory and power components marked in the diagram. Apply your own GPU thermal paste to the chip surfaces indicated by the applicator icons.
4Align the block, card, and backplate. Fit the insulating washers in the positions shown, tighten the spring screws gradually in a cross pattern, and secure the backplate with the remaining screws.
5Connect the tubing with G1/4 fittings and follow the inlet and outlet marks on the terminal.
6Fill the loop, then power only the pump to check for leaks. Keep the card and the rest of the system off until you confirm there are no leaks.
You’ll also need a pump, reservoir, radiator, G1/4 tubing fittings, tubing, and coolant.
Shaded memory and power components take pads. Applicator icons mark the surfaces for GPU thermal paste.
FAQ
How is the Cambricon MLU370-X8 cooled from the factory?
Cambricon lists a maximum thermal power of 250 W for the MLU370-X8. Its stock heatsink is passive and relies on airflow from the chassis.
What are the Cambricon MLU370-X8 card specs?
The stock accelerator has 48 GB of LPDDR5, a PCIe 4.0 ×16 interface, and a full-height, full-length, dual-slot form factor. Cambricon lists a peak of 256 TOPS at INT8.
Do I need a separate pump and radiator?
Yes. Connect the block to a custom cooling loop with a pump, reservoir, and radiator.
What should I check for chassis clearance?
Use the block and backplate dimensions above. Leave additional space at the terminal for G1/4 fittings and tubing.
Which thermal pads should I use?
Use the 1.5 mm pads at the memory and power-component contact points shown in the diagram.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.
- The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.