NVIDIA Tesla P4 Cooler, Full-Cover Water Block with Backplate (Fits Tesla T4) | Bykski N-TESLA-P4-X-V2

Bykski · N-TESLA-P4-X-V2

Full-cover water block for matching NVIDIA Tesla P4 and T4 PCBs

The Bykski N-TESLA-P4-X-V2 replaces the stock cooler on NVIDIA Tesla P4 and Tesla T4 cards that match the PCB layouts listed below. Its full-cover cold plate transfers heat from the GPU core, memory and power MOSFETs to coolant circulating in a custom loop. The block comes with a separate aluminum backplate.

Fits
Matching Tesla P4 / T4 PCBs
Cold plate
Nickel-plated copper
Port thread
G1/4
Lighting
None

Compatibility

Fits the following cards when their PCB matches Bykski’s listed layout.

  • ✓NVIDIA Tesla P4
  • ✓NVIDIA Tesla T4

A different PCB layout will prevent the block from fitting. Before ordering, compare your board outline, component positions and mounting holes with the drawing.

Bykski PCB layout drawing

Design Highlights

Parallel microchannels

Coolant flows between the fins to carry heat away from the cold plate.

Nickel-plated copper cold plate

The cold plate uses high-purity T2 copper with a nickel finish. Bykski lists a thermal conductivity of 401 W/(m·K) for the copper.

Key Specifications

Part numberN-TESLA-P4-X-V2
Block typeFull-cover GPU water block with backplate
Block materialsNickel-plated T2 copper cold plate, stainless steel panel and black POM terminal
BackplateBlack anodized aluminum, outside the coolant path
Port threadG1/4
Inlet and outletEither port can serve as the inlet, depending on tubing routing
ColorBlack with gunmetal
Block dimensions168.53 × 85.61 × 19.20 mm
Backplate dimensions167.60 × 64.46 × 6.00 mm
LightingNone

Which Version Do I Need?

Choose a cooler that matches your card’s PCB and the type of liquid cooling you plan to use.

Bykski N-TESLA-P4-X-V2THIS PAGE
A full-cover block with backplate for a custom loop and a Tesla P4 or T4 that matches the layout above.
An all-in-one cooler with a 360 mm radiator for a Tesla T4 that matches that kit’s PCB layout. The options are B-FRD-TESLA-T4-360 and B-FRD-TESLA-T4-360-H.
A separate water block with backplate for a custom loop and a Tesla T4 that matches this version’s PCB layout.

What's in the Box

1× full-cover GPU water block1× backplate1 set of mounting hardware

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Confirm that your card is a Tesla P4 or Tesla T4 and that its PCB matches the layout in Compatibility.
2
Remove the stock cooler and clean off old thermal material and residue.
3
Apply thermal paste to the GPU core. Check the required pad thickness before mounting. Place pads on the memory chips and MOSFETs in the dark areas shown in the drawing. Keep pads off the inductors.
4
Stack the block, PCB and backplate in that order and align the holes. Place insulating washers at the four holes around the GPU. Tighten the spring screws gradually in a diagonal pattern, then tighten the remaining backplate screws. Use even pressure and avoid overtightening.
5
Connect the G1/4 fittings and tubing. Power only the pump to test for leaks while the rest of the system stays off.

For a new custom loop, also plan for a pump, reservoir, radiator, G1/4 fittings for the block, tubing and coolant.

Dark areas mark thermal pad placement for memory and MOSFETs. Apply thermal paste to the GPU core in the center.

FAQ

Can I use this block on a custom PCB?

Compare your board with Bykski’s drawing. The block fits the listed Tesla P4 and T4 PCB layouts. A board with a different layout will not fit.

Do I need a pump and radiator?

Yes. This block connects to a custom liquid cooling loop with a pump, reservoir, radiator, fittings, tubing and coolant.

How is the stock NVIDIA Tesla P4 cooled?

The stock Tesla P4 is passively cooled and relies on airflow through the chassis. This full-cover water block replaces the stock cooler and connects to a custom liquid cooling loop.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.