Bykski · N-TESLA-A100-80G-X-V2
Full-cover GPU water block for NVIDIA A100 and A800 80GB PCIe
The Bykski N-TESLA-A100-80G-X-V2 is a full-cover GPU water block with an aluminum backplate for converting supported 80GB NVIDIA PCIe cards to custom liquid cooling. It replaces the stock passive heatsink and carries heat from the GPU core, memory and power delivery components into the loop through rear G1/4 ports.
Fits
NVIDIA A100 / A800 80GB PCIe
Coverage
GPU core, memory and VRM
Cold plate
Nickel-plated T2 copper
Compatibility
Supported cards with the specified PCB layout
- ✓NVIDIA A100 80GB PCIe (stock passive version)
- ✓NVIDIA A800 80GB PCIe (stock passive version)
Not compatible:
- ✗NVIDIA A100 40GB PCIe
- ✗NVIDIA A800 40GB Active
- ✗NVIDIA A100 80GB SXM
- ✗NVIDIA A800 80GB SXM4
Compare the mounting holes and component layout on your exact PCB with the Bykski reference before ordering.
Bykski NVIDIA A100 80GB PCIe PCB drawing. Compare the outline, mounting holes and component layout with your card.
Design Highlights
A copper cold plate for the GPU, memory and VRM
The nickel-plated T2 copper cold plate draws heat from the GPU core, memory and power delivery components. The rear G1/4 inlet and outlet sit in a POM terminal positioned to leave room for the NVLink bridge.
0.5 mm jet microchannels
Coolant flows through the cold plate’s fin section. Bykski specifies a 0.5 mm gap between fins.
Key Specifications
| Model | N-TESLA-A100-80G-X-V2 |
|---|
| Coverage | GPU core, memory and VRM |
|---|
| Cold plate | Nickel-plated T2 high-purity copper |
|---|
| Copper thermal conductivity | 401 W/(m·K), manufacturer-listed material value |
|---|
| Top panel | Stainless steel |
|---|
| Backplate | Black anodized aluminum, outside the coolant path |
|---|
| Microchannel gap | 0.5 mm |
|---|
| Inlet and outlet | Rear G1/4 ports in a POM terminal |
|---|
| Block dimensions | 264.45 × 96.31 × 35.54 mm (length × height × thickness) |
|---|
| Backplate dimensions | 218.52 × 95.86 × 6.00 mm (length × height × thickness) |
|---|
| Lighting | None |
|---|
Water block dimensions in millimeters, from Bykski’s drawing.
Which Version Do I Need?
Check the GPU’s memory size and board layout first. Compare the PCB guide for the 80GB cooler you plan to order.
N-TESLA-A100-80G-X-V2THIS PAGE
Choose this block and backplate if you’re building or upgrading a custom loop and want the rear G1/4 layout shown here.
A separate custom-loop block for the A100 and A800 80GB with its own cold plate and backplate design. Choose it when planning your build around the SR drawings.
Choose this A100 and A800 80GB all-in-one kit if you want the pump, radiator and fans supplied with the block. Check the radiator mount in your case.
What's in the Box
1 × full-cover GPU water block1 × aluminum backplate5 × 1.8 mm thermal pad stripsPort plug hardware4 × M3 × 5 mm bracket screws with washers4 × 0.5 mm insulating washers4 × M2 × 5 mm spring screws8 × M2 × 9.5 mm backplate screws
Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.
Installation & Use
1Power off the system. Remove the card and its stock heatsink, then clean off old thermal paste and pads. Check that the block’s screw holes line up with the PCB.
2Apply thermal paste to the GPU core. Cut the 1.8 mm strips to fit the memory and MOSFET areas shown in the guide. Leave the inductors bare.
3Align the block, PCB and backplate. Fit the insulating washers at the four holes around the GPU and tighten the spring screws gradually in a cross pattern. Secure the remaining holes with the backplate screws.
4Connect the loop with G1/4 fittings. Follow the IN and OUT markings on the rear terminal.
5Fill and leak-test the loop with only the pump powered. Check the joints before powering the GPU.
You also need a pump, reservoir, radiator with fans, G1/4 fittings sized for your tubing, tubing and coolant.
Bykski installation drawing. The center square shows the thermal paste area. Gray strips and patches mark the thermal pad locations.
FAQ
Will it fit an 80GB SXM card?
This block fits the NVIDIA 80GB PCIe cards listed above when their PCB layouts match Bykski’s compatibility guide. Check your card’s form factor and PCB before ordering.
Do I need a separate pump and radiator?
Yes. Use this block with a pump, reservoir and fan-cooled radiator in a custom loop. A pump-reservoir combo can fill both roles.
How do I check case clearance?
Use the block dimensions to check clearance around the card and leave room at the rear for the fittings and tubing. Check your case’s radiator mounts before choosing a radiator.
Can I keep the NVLink bridge?
Bykski positions the inlet and outlet at the rear to leave room for the bridge. Check that your fittings and tubing also clear it.
Can I water-cool my NVIDIA A100 or A800 80GB PCIe card?
Yes, if you have a stock passive card with a supported PCB. This water block replaces the original heatsink and connects to a custom liquid cooling loop. For an A800, confirm your exact board layout with Bykski before ordering.
Notes- This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.