Bykski · N-TESLA-L4-X
Full-cover water block for the NVIDIA L4
The Bykski N-TESLA-L4-X is a full-cover water block with an aluminum backplate for the 24 GB NVIDIA L4 Tensor Core PCIe card. It replaces the stock passive heatsink and transfers heat from the GPU, memory, and power stages to coolant, which carries it to a radiator in your custom loop.
Cold plate
Nickel-plated T2 copper
Compatibility
- ✓NVIDIA L4 Tensor Core GPU (Tesla L4, 24 GB PCIe)
The stock card is low-profile and single-slot. Compare your bare PCB with the installation diagram before ordering.
NVIDIA L4 with its stock heatsink (photo by ServeTheHome)
Design Highlights
Nickel-plated T2 copper
The cold plate spans the GPU, memory, and power stages. Bykski lists the T2 copper at 401 W/(m·K) and gives the copper plate a length of 139.73 mm.
Coolant path (manufacturer illustration)
Coolant flows through 0.3 mm microchannels
The flow path passes through a fin array over the GPU. Bykski lists up to 44 waterways and about 9,391 mm² of wetted surface area.
Two ports at one end
The inlet and outlet are together on the short end of the block, where you connect the tubing for your custom loop.
Key Specifications
| Model | N-TESLA-L4-X |
|---|
| Block type | Full-cover GPU block for a custom loop |
|---|
| Cold plate | Nickel-plated T2 copper |
|---|
| Body material | Metal and POM |
|---|
| Backplate | Black aluminum |
|---|
| Coolant connections | Two end ports |
|---|
| Block size | 185.40 × 87.84 × 16.00 mm |
|---|
| Backplate size | 157.60 × 71.60 × 5.00 mm |
|---|
Water block dimensions in mm (manufacturer drawing)
Which Version Do I Need?
Match the GPU model first. The L4 has 24 GB of memory, while the L40 is a separate 48 GB card.
N-TESLA-L4-X Water BlockTHIS PAGE
Choose this block if you already have a custom loop or want to select your own pump and radiator.
Choose this kit if you want a matched L4 block, inline pump, tubing, and 360 mm radiator. Check for a 360 mm radiator mount in your case.
What's in the Box
1 × full-cover GPU water block1 × aluminum backplate5 × 1.5 mm thermal pad strips4 × 0.5 mm insulating gaskets4 × M2 × 6 mm spring screws6 × M2 × 9.5 mm backplate screws
Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.
Installation & Use
1Shut down the system. Remove the L4 and its stock heatsink, then clean off the old paste and pads.
2Dry-fit the block to check that its standoffs line up with the PCB holes.
3Place the included 1.5 mm pads at the memory and power-stage contact areas and the rear contact areas shown in the diagram. Apply GPU thermal paste to the die.
4Fit the block and backplate. Position the insulating gaskets at the matching holes and tighten the spring and backplate screws gradually and evenly.
5Connect the block to your loop and fill it. Run the pump by itself to check for leaks before powering the card.
You also need a pump, a reservoir, a radiator with fans, tubing, coolant, and fittings that match the block ports and your tubing.
1 Water block · 2 Thermal pads · 3 L4 PCB · 4 Insulating gaskets · 5 Spring screws · 6 Backplate · 7 Backplate screws
FAQ
Does the NVIDIA L4 use passive cooling?
Yes. The stock L4 has a passive heatsink that relies on system airflow. NVIDIA specifies a maximum thermal design power of 72 W.
What is POM on this water block?
POM stands for polyoxymethylene. Bykski uses it alongside metal in the body of this block.
Do I need a separate pump and radiator?
Yes. Use this block in a custom loop with a pump and radiator.
How do I check case clearance?
Use the block and backplate dimensions above to check the space around the card. Leave additional room for fittings and tubing and verify you have a place to mount the radiator.
Notes- The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.