RTX 5090 Founders Edition GPU Water Block with Backplate – Bykski N-RTX5090FE-SR

Bykski · N-RTX5090FE-SR

Full-cover water block for the RTX 5090 Founders Edition

The Bykski N-RTX5090FE-SR is a full-cover GPU water block for the NVIDIA GeForce RTX 5090 Founders Edition. It replaces the stock cooler and uses your custom loop to cool the GPU die, memory, and power stages. The block has a T2 copper cold plate, G1/4 ports, and an included aluminum backplate.

Fits
RTX 5090 FE
Cold plate
T2 copper
Port thread
G1/4
Lighting
None

Compatibility

Bykski lists one compatible PCB layout.

  • ✓NVIDIA GeForce RTX 5090 Founders Edition (FE PCB)

Not compatible:

  • ✗RTX 5090 Turbo and other non-Founders Edition PCB layouts

Before ordering, verify the exact card model and compare its PCB and mounting holes with the board shown.

RTX 5090 Founders Edition shown with the stock cooler removed.

Design Highlights

One cold plate for the GPU, memory, and power stages

The T2 copper cold plate has raised contact areas for the card’s components. Inside the block, 0.3 mm jet microchannels guide coolant across the area above the GPU die.

Aluminum backplate for the rear of the card

The included aluminum backplate bolts to the rear of the PCB and sits outside the coolant path.

G1/4 inlet and outlet at the end

Use G1/4 fittings on the block and match the tubing side of each fitting to your tubing. Follow the inlet and outlet markings on the terminal when you route the loop.

Key Specifications

ModelN-RTX5090FE-SR
Cold plateT2 copper
BackplateAluminum, outside the coolant path
Cooling coverageGPU die, memory, and power stages
Port threadG1/4 female
Jet microchannel width0.3 mm
Block (L × W × T)234.35 × 121.82 × 22.70 mm
Backplate (L × W × T)222.16 × 121.82 × 10.96 mm
Net weight1.5 kg
Maximum working pressure2 bar
Working temperature−20 to 60 °C
LightingNone

Water block dimensions in millimeters.

Which Version Do I Need?

Bykski N-RTX5090FE-SRTHIS PAGE
Choose this water block for a Founders Edition card you plan to connect to a custom loop.
Choose this Founders Edition AIO if you want a kit with its own pump and 360 mm radiator.
Choose this separate water block if your card is the RTX 5090 32G D7 Turbo V1. Match the SKU when ordering.

What's in the Box

GPU water blockAluminum backplateThermal padsMounting hardware set

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Shut down and unplug the PC. Remove the card, take off the stock cooler, and clean off the old thermal material. Keep the original card hardware organized.
2
Cut the included thermal pads to fit the areas marked in red on the front and rear PCB diagrams, then peel off the protective film from both sides of each pad. Apply your own thermal paste to the GPU die.
3
Check that the mounting holes line up, then lower the block straight onto the card. Secure it with the mounting hardware, tightening gradually in a cross pattern.
4
Secure the backplate with its own screws. Check that the card’s original connector boards and the slot bracket line up before tightening the bracket hardware.
5
Connect the G1/4 fittings and tubing to the marked inlet and outlet. Fill and bleed the loop, then leak-test it before powering the card.

For a new loop, you also need a pump, reservoir, radiator, G1/4 fittings, tubing, and compatible coolant.

PCB front (top) and rear (bottom). Red outlines mark thermal pad locations. The blue outline marks the GPU die.

FAQ

Will this water block fit any RTX 5090?

It fits the NVIDIA GeForce RTX 5090 Founders Edition PCB. Check your card’s exact model and board layout before ordering.

Which fittings do I need?

Use fittings with G1/4 male threads on the block. Choose the tubing connection to match your tubing.

Does coolant flow through the backplate?

Coolant flows through the water block. The included aluminum backplate sits outside the coolant path.

Does this version have RGB lighting?

This configuration is unlit and needs no lighting connection.

Where do the thermal pads go?

Place the thermal pads on the areas marked in red on the front and rear PCB diagrams. Apply your own thermal paste to the GPU die, marked in blue.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
  • This product is designed for self-installation. The manufacturer is not liable for any damages resulting from misuse, including, but not limited to, improper installation or the use of incompatible hardware or fluids. By using this product, you accept all related risks.