Bykski · N-RTXPRO6000-WS-SR
Full-cover water block for the RTX PRO 6000 Blackwell Workstation Edition
The Bykski N-RTXPRO6000-WS-SR is a full-cover GPU water block with an aluminum backplate for the 96 GB NVIDIA RTX PRO 6000 Blackwell Workstation Edition. It replaces the card’s stock air cooler and transfers heat from the GPU, front-side memory, and power stages into a custom liquid-cooling loop through a nickel-plated T2 copper cold plate.
Fits
RTX PRO 6000 Blackwell Workstation Edition
Coverage
GPU + front-side VRAM + VRM
Cold plate
Nickel-plated T2 copper
Compatibility
Match the exact GPU edition
- ✓NVIDIA RTX PRO 6000 Blackwell Workstation Edition (96 GB GDDR7 ECC, PCIe 5.0 x16)
Not compatible:
- ✗NVIDIA RTX PRO 6000 Blackwell Server Edition
- ✗NVIDIA RTX PRO 6000 Blackwell Max-Q Workstation Edition
- ✗NVIDIA RTX 6000 Ada Generation
- ✗NVIDIA RTX A6000
- ✗NVIDIA GeForce RTX 4090
- ✗NVIDIA GeForce RTX 4080
- ✗Other consumer gaming graphics cards
Before ordering, compare your exact PCB with the Bykski reference photo.
Bykski reference PCB, GPU side.
Design Highlights
One cold plate covers the GPU, memory, and power stages
The nickel-plated T2 copper cold plate carries heat from the front of the card into the coolant. The loop’s radiator releases that heat away from the card.
Jet flow across 0.3 mm microchannels
Coolant passes through up to 56 microchannels in the cold plate. Bykski lists about 15,565 mm² of internal coolant contact area.
Aluminum backplate with thermal pads
The included backplate fits behind the PCB. The thermal pad placement diagram in Installation & Use shows the points of contact on the rear of the PCB.
Key Specifications
| Model | N-RTXPRO6000-WS-SR |
|---|
| Cooling type | Full-cover GPU block for a custom loop |
|---|
| Cold plate | T2 copper with electroless nickel plating |
|---|
| Copper thermal conductivity | 401 W/(m·K) |
|---|
| Cold plate length | 136.55 mm |
|---|
| Copper plate thickness | 9.5 mm |
|---|
| Base thickness under the microchannels | 0.35 mm |
|---|
| Nickel plating thickness | 0.001–0.002 mm |
|---|
| Backplate | Aluminum |
|---|
| Block dimensions | 233.85 × 121.82 × 20.70 mm |
|---|
| Backplate dimensions | 222.16 × 121.82 × 4.96 mm |
|---|
| Port thread | G1/4 |
|---|
| Seal | Single-layer EPDM sealing ring |
|---|
| Net weight | 1.5 kg |
|---|
| Maximum working pressure | 2 bar |
|---|
| Working temperature | −20 to 60 °C |
|---|
Bykski dimension drawing. Water block above, backplate below. Measurements in millimeters. In the orientation shown, the upper port is the outlet (OUT) and the lower port is the inlet (IN). Check the markings on your block before connecting tubing.
Which Version Do I Need?
Choose by GPU edition first, then by how you want to build the loop.
Bykski N-RTXPRO6000-WS-SR (custom-loop block)THIS PAGE
Choose this water block and backplate if you already have a custom loop or want to choose your own pump and radiator.
Choose this all-in-one kit for the same Workstation Edition if your case has room for a 360 mm radiator and fans. The kit includes the radiator, fans, and an inline pump.
What's in the Box
1 GPU water block1 aluminum backplate1 PCIe bracket1.5 mm thermal pads
Mounting hardware includes 4 × 0.5 mm spacers, 4 × M2 × 5 mm spring screws, 4 backplate screws, 8 × M2 × 3 mm flat-head screws, and 3 × M3 × 5 mm flat-head screws.
Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.
Installation & Use
1Power down, remove the card and its stock cooler, and clean away the old thermal paste and pads.
2Apply thermal paste to the GPU die. Cut the included 1.5 mm pads to size and place them on both sides of the PCB as shown in the thermal pad placement diagram below.
3Align the block and backplate with the mounting holes. Fit the spacers and screws as shown in the exploded view, then tighten evenly.
4At the display-output end, install the eight M2 × 3 mm flat-head screws at the mounting points beside the display connectors. Align the supplied PCIe bracket with the connectors and fasten it through its three mounting holes using the M3 × 5 mm flat-head screws.
5Connect the tubing with G1/4 fittings, fill and bleed the loop, then check for leaks with the GPU and other PC hardware unpowered.
You’ll also need a pump, reservoir, radiator with fans, tubing, G1/4 fittings that match your tubing, and coolant suitable for a nickel-plated copper loop. Have thermal paste ready for the GPU die.
1 Water block · 2 Pads · 3 Your GPU PCB · 4 Spacers · 5 Spring screws · 6 Backplate · 7 Backplate screws
Thermal pad placement. GPU side at left, rear of the PCB at right. Place the 1.5 mm pads on the memory and power-stage contact areas shown. Apply only thermal paste to the GPU die under the applicator in the center of the left view.
FAQ
Can I use this on a Max-Q or Server Edition card?
Bykski lists those editions under a different block. Use the N-RTXPRO6000-WS-SR for the standard Workstation Edition and check the PCB photo before ordering.
Do I need a separate pump and radiator?
Yes. The block connects to a custom loop with its own pump and radiator. The same-card all-in-one option includes them.
How do I check whether it will fit my case?
Use the block and backplate drawings to check the card area and leave room for the fittings and tube routing. Check the radiator and fan mounting space separately. NVIDIA rates the Workstation Edition at 600 W total board power for planning the loop.
Which thermal pads go on the back of the card?
Use the included 1.5 mm pads at the marked positions in the right-hand view of the thermal pad placement diagram in Installation & Use.
Notes- The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.
- All products are covered by a return policy.