RTX 3080 / 3080 Ti / 3090 Reference GPU Water Block with Active Backplate, Bykski N-RTX3090H-TC-V2

Bykski · N-RTX3090H-TC-V2

Full-cover GPU water block with an active backplate

The Bykski N-RTX3090H-TC-V2 replaces the stock cooler on select GeForce RTX 3080, 3080 Ti, and 3090 cards with the reference PCB layouts listed below. Its front block cools the GPU, memory, and voltage regulators. A bridge routes coolant through the active backplate to cool memory on the rear of the card where present.

Fits
Select RTX 3080 / 3080 Ti / 3090 reference PCBs
Backplate
Active liquid cooling
Loop ports
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Supported partner reference PCB layouts

  • ✓Galax RTX 3090 24GB SG (1-Click OC), 39NSM5MD1GNA
  • ✓Galax RTX 3090 24GB EX Gamer (1-Click OC), 39NXM5MD1JNA
  • ✓KFA2 RTX 3090 24GB SG (1-Click OC), 39NSM5MD1GNK
  • ✓Palit RTX 3090 24GB GamingPro, NED3090019SB-132BA
  • ✓Palit RTX 3090 24GB GamingPro OC, NED3090S19SB-132BA
  • ✓Gainward RTX 3090 24GB Phoenix
  • ✓Gainward RTX 3090 24GB Phoenix GS
  • ✓Manli RTX 3090 24GB Gallardo
  • ✓PNY RTX 3090 24GB XLR8 Gaming REVEL EPIC-X RGB Triple Fan, VCG309024TFXPPB
  • ✓EMTEK RTX 3090 24GB Black Edition OC
  • ✓Dell OEM RTX 3090 24GB
  • ✓ASUS EKWB RTX 3090 24GB
  • ✓KFA2 RTX 3080 Ti 12GB SG (1-Click OC), 38IOM5MD99DK
  • ✓Palit RTX 3080 Ti 12GB GamingPro, NED308T019KB-132AA
  • ✓Gainward RTX 3080 Ti 12GB Phoenix
  • ✓Gainward RTX 3080 Ti 12GB Phoenix GS
  • ✓Manli RTX 3080 Ti 12GB Gallardo
  • ✓PNY RTX 3080 Ti 12GB XLR8 Gaming REVEL EPIC-X RGB Triple Fan, VCG3080T12TFXPPB
  • ✓EMTEK RTX 3080 Ti 12GB Black Edition
  • ✓Leadtek WinFast RTX 3080 Ti 12GB Hurricane
  • ✓Galax RTX 3080 10GB SG (1-Click OC), 38NWM3MD99NN
  • ✓Galax RTX 3080 10GB EX Gamer (1-Click OC), 38NWM3MD1JAA
  • ✓KFA2 RTX 3080 10GB SG (1-Click OC), 38NWM3MD99NK
  • ✓Palit RTX 3080 10GB GamingPro (original model), NED3080019IA-132AA
  • ✓Palit RTX 3080 10GB GamingPro OC (original model), NED3080S19IA-132AA
  • ✓Gainward RTX 3080 10GB Phoenix (original model)
  • ✓Gainward RTX 3080 10GB Phoenix GS (original model)
  • ✓Manli RTX 3080 10GB Gallardo
  • ✓PNY RTX 3080 10GB XLR8 Gaming UPRISING EPIC-X RGB Triple Fan, VCG308010TFXMPB
  • ✓Maxsun RTX 3080 10GB iCraft OC
  • ✓Dell Alienware Aurora R12 RTX 3080 10GB
  • ✓Dell OEM RTX 3080 10GB
  • ✓Leadtek WinFast RTX 3080 10GB Hurricane

Not compatible:

  • ✗NVIDIA GeForce RTX 3090 Founders Edition
  • ✗NVIDIA GeForce RTX 3080 Ti Founders Edition
  • ✗NVIDIA GeForce RTX 3080 Founders Edition

Before ordering, confirm the exact card model and revision, then compare the entire PCB layout, including the mounting holes, components, and connectors.

Example PCB from Bykski’s guide. Front on the left, rear on the right.

Design Highlights

Coolant flows through the backplate

The bridge joins the coolant passages in the front block and rear plate. On cards with rear memory, thermal pads transfer heat from those chips to the active backplate.

Microchannels above the GPU

Coolant passes through fine channels above the GPU die. The T2 copper cold plate also contacts the front-side memory and voltage regulators through thermal pads.

Key Specifications

ModelN-RTX3090H-TC-V2
Store SKUN-RTX3090H-TC-V2_RBW
Front cold plateT2 copper
TopClear acrylic
Active backplateCopper contact plate with a coolant channel
Active backplate (L × W × T)215.32 × 97.68 × 17 mm
Loop port threadG1/4
Lighting5V 3-pin addressable RGB (RBW)

Active backplate dimensions in millimeters.

Which Version Do I Need?

Choose by how you want to cool the back of the card. Check the compatibility list for the block you select.

Bykski N-RTX3090H-TC-V2THIS PAGE
Choose this version to run coolant through the front block and the active backplate.
Choose this version if you want a front water block with a passive backplate.

What's in the Box

1 × full-cover GPU water block1 × active backplate1 × bridge module2 × G1/4 stop plugsMounting hardware and sealsThermal pads5V 3-pin ARGB lighting

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Main parts shown, with the active backplate above the front block and the bridge on the right.

Installation & Use

1
Power off the system, remove the card, and take off the stock cooler. Clean away the old thermal materials and dry-fit the block to check the mounting holes.
2
Apply thermal pads at the block’s contact points for the exact PCB. Pad the rear memory where it contacts the active backplate, and apply your own thermal paste to the bare GPU die.
3
Fit the PCB between the front block and active backplate. Position the insulating washers and tighten the spring screws gradually in a diagonal pattern. Secure the remaining backplate screws.
4
Seat the seals in the matching grooves on the supplied bridge, then attach the bridge to both cooling plates. Tighten the bridge screws evenly without overtightening.
5
Connect your G1/4 fittings and tubing to the bridge’s marked inlet and outlet. Plug unused ports and leak-test the loop while the card is unpowered.

For a custom loop, supply a pump, radiator, coolant, tubing, and G1/4 fittings. Use a compatible Bykski 5V RBW controller. For a motherboard connection, use a matching 5V 3-pin ARGB adapter if the lead has the native Bykski plug. Do not connect the lead to a 12V RGB header.

The clear bridge is shown fitted to the block.

FAQ

Does this block fit every RTX 3080 reference card?

Check your exact card model and PCB revision against the list above. If your card is absent, send a photo of the bare PCB for a fit check before ordering.

Does coolant flow through the backplate?

Yes. The included bridge routes coolant through both the front block and active backplate.

Which fittings does this water block take?

Use G1/4 fittings at the bridge and seal any unused ports with the supplied stop plugs.

How do I connect the lighting?

Use a compatible Bykski 5V RBW controller. For a motherboard connection, use a matching 5V 3-pin ARGB adapter if the lead has the native Bykski plug. A 12V RGB header can damage the lighting.

Notes
  • This is a repair or replace only item. Returns not accepted on compatibility issues or if block has had water/fluid run through it.
  • Manufacturer reserves right to alter block design to expand compatibility. Delivered item may not 100% match pictured item.
  • Not responsible for any damage caused by or when using this product. Please use at your own risk.
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.