Bykski · N-AS3090TURBO-X
Full-cover water block for ASUS RTX 3080 Ti Turbo and RTX 3090 Turbo
The Bykski N-AS3090TURBO-X is a full-cover water block for supported ASUS RTX 3080 Ti Turbo and RTX 3090 Turbo graphics cards. It replaces the stock cooler and transfers heat from the GPU, memory, and voltage regulators to the coolant in a custom loop. The kit includes a passive aluminum backplate and 5V addressable lighting.
Fits
Select ASUS Turbo PCBs
Backplate
Passive aluminum
Compatibility
Supported ASUS Turbo PCB layouts
- ✓ASUS Turbo GeForce RTX 3080 Ti (TURBO-RTX3080TI-12G)
- ✓ASUS Turbo GeForce RTX 3090 (TURBO-RTX3090-24G)
Not compatible:
- ✗ASUS TUF Gaming or ASUS ROG Strix PCB layouts
Before ordering, check the exact model on your card and verify the full PCB layout for that model.
ASUS Turbo GeForce RTX 3090 shown with its original cooler.
Design Highlights
Full-cover cold plate
The copper cold plate draws heat from the GPU, memory, and voltage regulators. The clear acrylic cover lets you see the coolant channels.
Bykski jet microchannel illustration.
Jet microchannels
Coolant flows between the fine fins in the cold plate. Connect your loop to the marked inlet and outlet with G1/4 fittings.
5V addressable lighting
The included RBW light strip illuminates the clear acrylic cover.
Key Specifications
| Model | N-AS3090TURBO-X |
|---|
| Cold plate | Nickel-plated T2 high-purity copper |
|---|
| Cover | Clear PMMA acrylic |
|---|
| Backplate | Black aluminum, passive |
|---|
| Coverage | GPU core, memory, and voltage regulators |
|---|
| Port thread | G1/4 inlet and outlet |
|---|
| Block size (L × W × T) | 266.59 × 127.54 × 23.50 mm |
|---|
| Lighting | 5V 3-pin ARGB (RBW) |
|---|
Bykski drawing. Dimensions are in millimeters.
Which Version Do I Need?
Find the series on your ASUS card label, then check the exact PCB against the compatibility list for the block you choose.
Bykski N-AS3090TURBO-XTHIS PAGE
Choose this block for either Turbo PCB listed above. It includes a passive backplate.
Check this active-backplate block if your card is an ASUS TUF Gaming model.
Check this active-backplate block if your card is an ASUS ROG Strix model.
What's in the Box
1 × full-cover GPU water block1 × passive aluminum backplate2× G1/4 stop plugs1 × mounting hardware setThermal pads1 × 5V ARGB light strip
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Water block and backplate.
Installation & Use
1Turn off the system, remove the graphics card, and take off its stock cooler.
2Clean off the old thermal paste and pads. Verify that the block’s mounting holes align with the PCB.
3Place the thermal pads at the contact points shown in the mounting instructions and apply your own thermal paste to the GPU die.
4Align the water block, PCB, and backplate. Install the washers and screws in the positions shown in the mounting instructions and tighten them evenly.
5Connect tubing to the marked inlet and outlet with G1/4 fittings. Seal unused ports with the stop plugs.
6Leak-test the loop before powering the graphics card.
You also need a pump, radiator, G1/4 fittings, tubing, and coolant. For lighting, use a compatible 5V ARGB controller or a matching adapter for a 5V 3-pin motherboard header.
Contact side of the water block.
FAQ
Will this fit my ASUS RTX 3080 Ti?
It fits the ASUS Turbo GeForce RTX 3080 Ti (TURBO-RTX3080TI-12G) with the listed PCB layout. Check the model number and PCB before ordering.
Does coolant run through the backplate?
The included aluminum backplate is passive. Coolant runs through the front water block.
Which fittings do I need?
Use G1/4 fittings for the inlet and outlet.
Can I plug the lighting into a 12V RGB header?
A 12V 4-pin RGB header can damage the light strip. Use a compatible 5V ARGB controller or a matching adapter for a 5V 3-pin motherboard header.
Notes- This is a repair or replace only item. Returns not accepted on compatibility issues or if block has had water/fluid run through it.
- Manufacturer reserves right to alter block design to expand compatibility. Delivered item may not 100% match pictured item.
- Not responsible for any damage caused by or when using this product. Please use at your own risk.
- The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.