Bykski · A-AS9070TUF-X
Full-cover water block for the ASUS TUF RX 9070 OC
The Bykski A-AS9070TUF-X replaces the stock cooler on the ASUS TUF Gaming Radeon RX 9070 OC Edition 16GB. Its copper cold plate transfers heat from the GPU, memory, and voltage regulators to your custom liquid cooling loop. The kit includes a black aluminum backplate, and the block connects through G1/4 ports.
Compatibility
- ✓ASUS TUF Gaming Radeon RX 9070 OC Edition 16GB (TUF-RX9070-O16G-GAMING)
Before ordering, confirm the full ASUS model number and compare your PCB layout and mounting holes with Bykski’s board photo. If the model number or PCB differs, ask FormulaMod to check the fit before ordering.
Bykski’s ASUS TUF RX 9070 PCB photo for checking the board layout.
Design Highlights
Clear top and separate aluminum backplate
The acrylic top exposes the coolant channels. The black aluminum backplate mounts behind the PCB, outside the coolant path.
0.3 mm microchannels
Coolant crosses the cold plate through up to 50 microchannels. The 133.27 mm copper plate extends over the GPU, memory, and power delivery contact areas.
5V addressable lighting
The RBW lighting works with a compatible 5V 3-pin ARGB setup. Connecting it to a 12V 4-pin RGB header can damage the lighting.
Key Specifications
| Model | A-AS9070TUF-X |
|---|
| Cold plate | T2 copper |
|---|
| Top | Clear acrylic (PMMA) |
|---|
| Backplate | Black aluminum |
|---|
| Port thread | G1/4 inlet and outlet |
|---|
| Microchannels | 0.3 mm |
|---|
| Block (L × W × T) | 219.90 × 155.67 × 26.27 mm |
|---|
| Backplate (L × W × T) | 219.90 × 125.48 × 5.94 mm |
|---|
| Lighting | 5V 3-pin ARGB (RBW) |
|---|
Manufacturer drawings in millimeters. Water block above, backplate below.
Which Version Do I Need?
Match the graphics card brand, series, and PCB to the block’s compatibility list before choosing a model.
Bykski A-AS9070TUF-XTHIS PAGE
Choose this block for the ASUS TUF RX 9070 OC model shown above.
For a Sapphire NITRO+ Radeon RX 9070 or NITRO+ Radeon RX 9070 XT, check the exact PCB against this listing.
Check this listing for the GIGABYTE RX 9070 XT GAMING OC 16G.
What's in the Box
1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugsThermal pad setMounting hardware set
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
1Turn off the system, remove the card, and take off the stock cooler and backplate. Clean off old thermal material.
2Follow Bykski’s installation diagram to trim the included thermal pads for the designated memory and power delivery contact points. Peel off the protective films and apply your own thermal paste to the bare GPU die.
3Align the water block and backplate with the PCB. Use the washers and the two sets of screws in the positions shown, and tighten evenly. If the block does not sit flat, check the fit before tightening further.
4Connect the G1/4 fittings according to the inlet and outlet markings on the block. Plug unused ports, then leak-test the loop before powering the graphics card.
Also needed for the loop: a pump, radiator, G1/4 tubing fittings, tubing, and coolant.
1 block · 2 thermal pads · 3 your graphics card PCB · 4 washers · 5 spring screws · 6 backplate · 7 backplate screws.
FAQ
Which ASUS RX 9070 PCB should I check?
Match ASUS model TUF-RX9070-O16G-GAMING and compare the board layout and mounting holes with the photo above.
What fittings connect to the block?
Use G1/4 loop fittings with a tube connection sized for your tubing.
Which lighting header do I use?
Use a compatible 5V 3-pin ARGB connection. Keep the lighting off 12V 4-pin RGB headers.
What thermal pads go on the card?
Bykski’s installation diagram for this model specifies 1.5 mm pads.
Notes- This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
- This product is designed for self-installation. The manufacturer is not liable for any damages resulting from misuse, including, but not limited to, improper installation or the use of incompatible hardware or fluids. By using this product, you accept all related risks.