RTX 3090 Ti Water Block for Gigabyte Gaming OC 24G, Bykski N-GV3090TIGMOC-X with Backplate

Bykski · N-GV3090TIGMOC-X

Full-cover water block for Gigabyte RTX 3090 Ti Gaming OC 24G

The Bykski N-GV3090TIGMOC-X replaces the stock cooler on the Gigabyte GeForce RTX 3090 Ti Gaming OC 24G for use in a custom liquid cooling loop. Its copper cold plate cools the GPU, memory, and voltage regulators. The block connects through G1/4 ports and comes with a passive aluminum backplate.

Fits
Gigabyte RTX 3090 Ti Gaming OC 24G
Ports
G1/4
Cold plate
Copper
Lighting
5V 3-pin ARGB

Compatibility

PCB match required.

  • ✓Gigabyte GeForce RTX 3090 Ti Gaming OC 24G (GV-N309TGAMING OC-24GD)

Before ordering, check the model number on your card and compare the full PCB layout and mounting holes with the board photo in the product gallery. Contact support if you need help confirming the match.

Gigabyte GeForce RTX 3090 Ti Gaming OC 24G with its original cooler.

Design Highlights

One block cools the GPU, memory, and VRM

The cold plate picks up heat from the GPU core, graphics memory, and voltage regulators. Coolant carries that heat away through the block.

Jet microchannels

Coolant passes between the closely spaced fins over the GPU contact area. The clear acrylic top leaves the flow path visible.

5V addressable lighting

The included RBW strip lights the clear top. Use a compatible 5V ARGB controller or an adapter for a 5V 3-pin motherboard header. A 12V RGB header can damage the strip.

Key Specifications

Manufacturer modelN-GV3090TIGMOC-X
Cold plateHigh-purity copper
TopClear acrylic
BackplateBlack aluminum, passive
Cooling coverageGPU core, graphics memory, and voltage regulators
Inlet and outlet threadG1/4
Water block (L × W × T)229.87 × 167.13 × 23.25 mm
Backplate (L × W × T)229.87 × 136.91 × 6.00 mm
Lighting5V 3-pin addressable RGB (RBW)

Water block above, backplate below. Dimensions are in millimeters.

Which Version Do I Need?

Start with the model on your card’s label. Each of these blocks is made for a specific PCB layout.

Bykski N-GV3090TIGMOC-XTHIS PAGE
Choose this block for the Gigabyte RTX 3090 Ti Gaming OC 24G after matching its PCB.
Check this block for the MSI GeForce RTX 3090 Ti Gaming X Trio 24G or Suprim X 24G.
Check this block if your card is the NVIDIA GeForce RTX 3090 Founders Edition. Confirm the exact GPU name on your card before ordering.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × mounting hardware set1 × thermal pad set1 × 5V ARGB light strip

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the PC and remove the graphics card. Remove the factory cooler and clean off old paste and pad residue.
2
Confirm that the mounting holes line up. Place the supplied thermal pads at the memory and MOSFET contact points. Leave the inductors clear. Apply your own thermal paste to the GPU die.
3
Align the water block, PCB, and backplate. Fit the insulating washers at the GPU mounting holes, tighten the spring screws gradually in a diagonal pattern, then secure the backplate screws.
4
Connect your G1/4 fittings to the marked inlet and outlet and close the unused ports with the stop plugs. Connect the lighting to a compatible 5V ARGB connection.
5
Fill and leak-test the loop with only the pump powered. Keep the graphics card off until the loop passes the check.

For a new loop, you also need a pump and reservoir, a radiator with fans, tubing, matching G1/4 fittings, and coolant.

1 Water block · 2 Thermal pads · 3 Graphics card PCB · 4 Insulating washers · 5 Spring screws · 6 Backplate · 7 Backplate screws

FAQ

How do I check whether this RTX 3090 Ti water block fits my card?

Check for Gigabyte GeForce RTX 3090 Ti Gaming OC 24G and the part number GV-N309TGAMING OC-24GD on the card label. Compare your PCB with the board photo in the product gallery before ordering.

What fittings does the block take?

It takes G1/4 fittings at the inlet and outlet. Choose fittings made for the tubing used in your loop.

Does the backplate need its own coolant connection?

The included black aluminum backplate is passive. Coolant flows through the front block.

Can I connect the lighting to a 12V RGB header?

Use a compatible 5V ARGB controller or an adapter to a 5V 3-pin motherboard ARGB header. A 12V RGB connection can damage the strip.

What else do I need to water-cool my 3090 Ti?

To build the loop, you’ll need a pump and reservoir, a radiator with fans, G1/4 fittings, tubing, and coolant.

Notes
  • This is a repair or replace only item. Returns not accepted on compatibility issues or if block has had water/fluid run through it.
  • Manufacturer reserves right to alter block design to expand compatibility. Delivered item may not 100% match pictured item.
  • Not responsible for any damage caused by or when using this product. Please use at your own risk.
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.