MSI RTX 4060 Ti Ventus 2X 16GB Water Block with Backplate — Bykski N-MS4060TIVES-X

Bykski · N-MS4060TIVES-X

Full-cover water block for the MSI RTX 4060 Ti Ventus 2X 16GB

The Bykski N-MS4060TIVES-X replaces the factory cooler on the MSI GeForce RTX 4060 Ti Ventus 2X 16GB with the PCB layout shown below. The T2 copper cold plate transfers heat from the GPU core, memory, and voltage regulators to a custom liquid cooling loop. The block comes with a black aluminum backplate.

Fits
MSI RTX 4060 Ti Ventus 2X 16GB
Port thread
G1/4
Lighting
5V 3-pin ARGB
Block length
164.64 mm

Compatibility

Bykski lists this card and PCB layout.

  • ✓MSI GeForce RTX 4060 Ti Ventus 2X 16GB

The board Bykski uses to illustrate compatibility is marked MS-V517 VER:1.0. Before ordering, confirm the full model name and compare your PCB’s component layout and mounting holes with Bykski’s diagram.

Design Highlights

T2 copper cold plate

The T2 copper cold plate has jet microchannels over the GPU core. The full-cover design also draws heat from the memory and voltage regulators through thermal pads.

Bykski’s coolant flow illustration.

G1/4 ports on both sides of the terminal

Use the top or bottom port positions to route the tubing in your case. Follow the inlet and outlet markings on the block and cap the unused ports.

5V addressable lighting

The RBW strip lights the clear acrylic top. The included sync cable connects it to a 5V 3-pin ARGB motherboard header.

Key Specifications

ModelN-MS4060TIVES-X
Cold plateT2 copper
TopClear acrylic
BackplateBlack aluminum
Cooling coverageGPU core, memory, and voltage regulators
Port threadG1/4
Block (L × W × T)164.64 × 150.69 × 26.75 mm
Backplate (L × W × T)164.64 × 121.18 × 6.00 mm
Lighting5V 3-pin ARGB (RBW)

Which Version Do I Need?

Check whether your MSI Ventus 2X is an RTX 4060 Ti or RTX 4060, then verify your card’s exact PCB layout.

Bykski N-MS4060TIVES-XTHIS PAGE
For the MSI RTX 4060 Ti Ventus 2X 16GB with the PCB shown above.
For the MSI RTX 4060 Ventus 2X Black 8GB OC. Check the linked listing for its PCB layout.

What's in the Box

1 × full-cover GPU water block with 5V ARGB strip1 × black aluminum backplate2 × G1/4 stop plugsThermal padsMounting hardware set (washers, spring screws and backplate screws)1 × lighting sync cable

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

1 Water block · 2 Thermal pads · 3 Your graphics card · 4 Washers · 5 Spring screws · 6 Backplate · 7 Backplate screws.

Installation & Use

1
Turn off the system. Remove the graphics card, take off its factory cooler and backplate, and clean off the old thermal interface material.
2
Cut the supplied thermal pads to fit the marked memory and power components. Apply your own GPU thermal paste to the GPU die.
3
Check that the mounting holes line up, then secure the water block and backplate with the supplied washers and screws.
4
Connect the G1/4 fittings and tubing to the marked inlet and outlet. Install stop plugs in the unused ports.
5
For lighting, connect the sync cable to a 5V 3-pin ARGB header with the arrow aligned to +5V. Leak-test the loop before powering the graphics card.

You also need a pump, radiator, G1/4 loop fittings, tubing, and coolant.

The dark strips and rectangles mark the thermal pad locations. The gray square marks the GPU die.

FAQ

Which MSI RTX 4060 Ti does this water block fit?

Bykski lists the Ventus 2X 16GB with the PCB layout shown above. Compare the full board layout and hole positions before ordering.

Does the water block come with a backplate?

Yes. The supplied black aluminum backplate mounts behind the PCB, outside the coolant path.

Which RGB header should I use?

Use a 5V 3-pin ARGB header with the supplied sync cable. A 12V 4-pin RGB header can damage the lighting.

What size fittings do I need?

Use G1/4 fittings for the inlet and outlet. Use the included stop plugs to seal the unused ports.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.