Bykski · N-RTXPRO6000-SR
Full-cover GPU water block for NVIDIA RTX PRO Blackwell
The Bykski N-RTXPRO6000-SR is a full-cover water block that replaces the stock cooler on the NVIDIA RTX PRO 6000 Blackwell Server Edition and other PCB layouts listed below. Its T2 copper cold plate transfers heat from the GPU core, memory, and power stages to a custom liquid cooling loop. The included aluminum backplate mounts behind the card.
Fits
RTX PRO 6000 Blackwell Server Edition
Ports
G1/4 inlet and outlet
Backplate
Aluminum, included
Compatibility
RTX 6000 PCB layout
- ✓NVIDIA RTX PRO 6000 Blackwell Server Edition
- ✓NVIDIA RTX PRO 6000 Blackwell Max-Q Workstation Edition
- ✓NVIDIA RTX PRO 6000D (84 GB)
- ✓RTX 5000 PCB layoutNVIDIA RTX PRO 5000 Blackwell (48 GB)
Not compatible:
- ✗NVIDIA RTX PRO 6000 Blackwell Workstation Edition (standard model)
- ✗NVIDIA RTX 6000 Ada
- ✗NVIDIA RTX A6000
- ✗NVIDIA GeForce gaming cards, including RTX 4090 and RTX 4080
Confirm your exact card model before ordering. For the RTX 6000 layout, compare the front of your PCB with Bykski’s diagram.
Check the RTX PRO 5000 Blackwell (48 GB) against its own PCB layout. If you need help verifying either layout, send FormulaMod the exact card model and a photo of the entire bare PCB.
Bykski’s front-side PCB diagram for the RTX 6000 layout.
Design Highlights
Bykski cold plate illustration.
A single cold plate for the GPU, memory, and power stages
Coolant moves through 0.3 mm jet microchannels in the copper cold plate before returning to the loop.
Separate inlet and outlet
The two G1/4 ports sit together on the end of the block. Follow the inlet and outlet markings when you route the tubing.
Aluminum backplate
The included backplate mounts to the rear of the PCB. Coolant flows through the water block on the front of the card.
Key Specifications
| Model | N-RTXPRO6000-SR |
|---|
| Cold plate | T2 copper |
|---|
| Cold plate length | 185.6 mm |
|---|
| Copper base thickness | 9.5 mm |
|---|
| Base thickness at the GPU core | 0.35 mm |
|---|
| Jet microchannels | 0.3 mm wide, up to 56 channels |
|---|
| Backplate | Black aluminum, passive |
|---|
| Ports | 2 × G1/4 female (inlet and outlet) |
|---|
| Water block (L × W × T) | 271.07 × 97.77 × 16.98 mm |
|---|
| Backplate (L × W × T) | 188.33 × 95.49 × 3.96 mm |
|---|
| Net weight | 1.4 kg |
|---|
| Max. working pressure | 4 bar |
|---|
| Working temperature | −20 to 60 °C |
|---|
| Seal material | EPDM |
|---|
| Bykski-listed fluid types | Water, ethylene glycol, propylene glycol, fluorinated fluids, mineral oil |
|---|
| Lighting | None |
|---|
Bykski dimension drawing in millimeters. Water block above, backplate below.
Which Version Do I Need?
Bykski N-RTXPRO6000-SRTHIS PAGE
Choose this block for the listed Server Edition, Max-Q, 6000D, or RTX PRO 5000 Blackwell (48 GB) PCB layout.
Choose this block for the standard RTX PRO 6000 Blackwell Workstation Edition and check your PCB against its listing.
Choose this separate block for an RTX 6000 Ada and check your PCB against its listing.
What's in the Box
1 × GPU water block1 × aluminum backplateThermal padsMounting hardware set
Supply your own G1/4 stop plug if you need to cap an unused port.
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
1Power off the system and remove the graphics card. Take off its stock cooler and clean away the old thermal materials.
2Use the pad-placement diagram for your exact PCB to trim and position the pads. Bykski’s illustrated pad layout is for the RTX 6000 PCB. For the RTX PRO 5000, confirm its pad positions before cutting. Apply a thin layer of thermal paste to the GPU die.
3Align the block and backplate with the card. Use the mounting diagram for your PCB to check the washer and screw positions, then tighten the assembly evenly.
4Connect your tubing with G1/4 fittings, following the inlet and outlet markings on the block.
5Fill and bleed the loop, then check for leaks before powering the graphics card.
For the loop, you also need a pump, radiator, reservoir, G1/4 fittings, tubing, and coolant.
Bykski assembly example for the RTX 6000 PCB layout. Use the installation diagram for your own PCB to confirm pad placement. 1 water block · 2 thermal pads · 3 graphics card PCB · 4 washers · 5 spring screws · 6 backplate · 7 backplate screws.
FAQ
Which RTX PRO 6000 Blackwell editions fit?
This block fits the listed Server Edition and Max-Q Workstation Edition PCB layouts. The standard Workstation Edition takes the Bykski N-RTXPRO6000-WS-SR.
Which RTX PRO 5000 Blackwell model fits?
Bykski lists NVIDIA RTX PRO 5000 Blackwell under the RTX 5000 PCB layout. NVIDIA specifies 48 GB for that model. If you need a fit check, send FormulaMod your exact card model and a photo of the entire bare PCB.
Is this an active backplate?
The included aluminum backplate is passive. Only the front block connects to the coolant loop.
What fittings do I need?
Use G1/4 fittings that match your tubing. Follow the inlet and outlet markings when connecting the block.
Do I need to connect a lighting cable?
This version has no lighting or RGB connection.
Notes- This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
- This product is designed for self-installation. The manufacturer is not liable for any damages resulting from misuse, including, but not limited to, improper installation or the use of incompatible hardware or fluids. By using this product, you accept all related risks.