RTX 4070 Ti SUPER / 4070 Ti Water Block for ZOTAC X-GAMING OC — Bykski N-ST4070TIXG-X

$146.41 piece
items available
View Details
Bykski · N-ST4070TIXG-X

Full-cover water block for select ZOTAC RTX 4070 Ti SUPER and 4070 Ti cards

The Bykski N-ST4070TIXG-X is a full-cover GPU water block for a custom liquid-cooling loop. It replaces the stock cooler on supported ZOTAC cards, including the GeForce RTX 4070 Ti SUPER 16GB X-GAMING OC. Its copper cold plate cools the GPU core, memory, and voltage regulators, and an aluminum backplate mounts behind the card.

Fits
Select ZOTAC X-GAMING OC and AMP AIRO PCBs
Cold plate
T2 copper
Ports
G1/4 inlet and outlet
Lighting
5V 3-pin ARGB

Compatibility

Bykski lists these exact ZOTAC GeForce models for this block.

  • ✓ZOTAC GeForce RTX 4070 Ti SUPER 16GB X-GAMING OC
  • ✓ZOTAC GeForce RTX 4070 Ti SUPER 16GB X-GAMING OC Opal White
  • ✓ZOTAC GeForce RTX 4070 Ti 12GB X-GAMING OC
  • ✓ZOTAC GeForce RTX 4070 Ti 12GB AMP AIRO (ZT-D40710F-10P)
  • ✓ZOTAC GeForce RTX 4070 12GB X-GAMING OC Opal White

Bykski groups the listed Ti and Ti SUPER models under its RTX 4070 Ti PCB layout. The RTX 4070 Opal White is in the separate RTX 4070 layout group.

Before ordering, verify your exact card model and check its bare PCB layout, component positions, and mounting holes.

ZOTAC RTX 4070 12GB X-GAMING OC Opal White PCB. Photo by PConline.

Design Highlights

One cold plate for the GPU, memory, and VRMs

Thermal paste transfers heat from the GPU die to the cold plate. Thermal pads connect the memory and voltage regulators to the same plate.

Jet microchannels

The block uses a three-layer design that routes coolant through the cold plate’s jet microchannels.

5V addressable lighting

The 5V ARGB strip lights the clear acrylic top. Use a 5V 3-pin ARGB header with a matching adapter or a compatible 5V controller. A 12V 4-pin RGB header can damage the strip.

Key Specifications

Model (SKU)N-ST4070TIXG-X
Cold plateT2 copper
TopClear acrylic
BackplateBlack aluminum, outside the coolant path
Cooling coverageGPU core, memory, and voltage regulators
Port threadG1/4
Block (L × W × T)190.00 × 137.15 × 26.35 mm
Backplate (L × W × T)190.00 × 106.65 × 7.50 mm
Lighting interface5V 3-pin ARGB (RBW)

Bykski’s dimension drawing. Water block above, backplate below. All measurements are in millimeters.

Which Version Do I Need?

Check your exact ZOTAC model name or SKU.

Bykski N-ST4070TIXG-XTHIS PAGE
Choose this block for the RTX 4070 Ti 12GB AMP AIRO after checking the PCB layout.
For the RTX 4070 Ti 12GB AMP Extreme AIRO, see this full-armor block and verify your PCB against its listing.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugsThermal pad setMounting hardware set1 × 5V ARGB LED strip

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the system and remove the card. Take off the stock cooler and clean the old thermal material from the GPU, memory, and voltage regulators.
2
Check the block’s contact surfaces and mounting holes against your PCB. Place the thermal pads on the matching memory and VRM contacts and spread a thin layer of your own thermal paste on the GPU die.
3
Align the block, PCB, and backplate. Install the washers and screws in their matching positions and tighten gradually with even pressure.
4
Connect the loop with G1/4 fittings at the marked inlet and outlet. Seal unused openings with the stop plugs.
5
Leak-test the loop with the graphics card unpowered.

You also need a pump, radiator, tubing, coolant, and G1/4 fittings sized for your tubing.

1 water block · 2 thermal pads · 3 your card’s PCB · 4 washers · 5 spring screws · 6 mounting screws · 7 backplate · 8 backplate screws

FAQ

Will this water block fit my ZOTAC RTX 4070 Ti SUPER?

Bykski lists the ZOTAC GeForce RTX 4070 Ti SUPER 16GB X-GAMING OC and its Opal White version. Check the full card name and bare PCB layout before ordering.

Which block fits the ZOTAC RTX 4070 Ti AMP AIRO?

This Bykski block lists the 12GB AMP AIRO (ZT-D40710F-10P). For the 12GB AMP Extreme AIRO, see the Granzon block in the version guide above.

How large is the water block?

The block measures 190.00 × 137.15 × 26.35 mm (L × W × T). Allow space for your fittings and tubing when you check case clearance.

What fittings do I need?

The block has G1/4 ports. Choose fittings that also match your tubing, and use the included plugs to seal unused openings.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.