XFX RX 6800 / RX 6800 XT V2 Overseas Edition Water Block — Bykski A-XF6800-X

Bykski · A-XF6800-X

Full-cover water block for select XFX Radeon RX 6800 cards

The Bykski A-XF6800-X replaces the stock cooler on compatible XFX cards, including the Radeon RX 6800 Overseas Edition with the PCB layout shown below. Its nickel-plated copper cold plate transfers heat from the GPU core, memory, and power delivery components to a custom liquid cooling loop. A black aluminum backplate mounts behind the card.

Fits
XFX RX 6800 / RX 6800 XT V2 Overseas Edition
Cooling coverage
GPU core, memory, and VRM
Port thread
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Bykski lists these XFX versions for the PCB layout shown.

  • ✓XFX Radeon RX 6800 Overseas Edition
  • ✓XFX Radeon RX 6800 XT Overseas Edition V2

Not compatible:

  • ✗XFX Radeon RX 6800 XT Speedster MERC 319 V1 PCB for A-XF6900XT-X

Before ordering, confirm your card’s exact edition and compare the entire PCB, including the mounting holes and component layout, with the drawing.

Bykski’s PCB layout drawing for the A-XF6800-X.

Design Highlights

Bykski’s illustration of coolant flow through the block.

Full-cover cooling

A nickel-plated T2 copper cold plate transfers heat from the GPU core, memory, and power delivery components to the coolant. The clear acrylic top lets you see the channels.

Bykski’s microchannel detail.

Jet microchannels

Coolant passes through fine channels in the cold plate above the GPU core.

5V addressable lighting

Connect the RBW strip to a 5V 3-pin ARGB header or a compatible 5V ARGB controller. Keep it off 12V 4-pin RGB headers.

Key Specifications

ModelBykski A-XF6800-X
Retail SKUA-XF6800-X_RBW
Cooling coverageGPU core, memory, and VRM
Cold plateNickel-plated T2 copper
TopClear acrylic
BackplateBlack aluminum
Backplate (L × H × T)266.49 × 117.48 × 6.00 mm
Inlet and outlet threadG1/4
Lighting connector5V 3-pin ARGB (RBW)

Bykski backplate drawing. Dimensions are in millimeters.

Which Version Do I Need?

Two XFX Radeon RX 6800 XT board layouts use different blocks. Match the PCB before choosing a block.

Bykski A-XF6800-XTHIS PAGE
Choose this block for the RX 6800 Overseas Edition or RX 6800 XT Overseas Edition V2 when your PCB matches the layout above.
Compare this block if you have an RX 6800 XT Speedster MERC 319 V1. Check its listing against your PCB.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugsMounting hardware setThermal pads1 × 5V ARGB light stripLighting sync cable

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the system, remove the graphics card, and take off the stock cooler. Clean the old thermal material from the GPU and the other contact surfaces.
2
Place thermal pads on the memory and MOSFET contact points specified for your PCB and mounting kit. Apply your own thermal paste to the GPU die.
3
Align the block with the card’s mounting holes. Fit the included backplate and tighten the hardware gradually so the block seats evenly.
4
Connect the inlet and outlet with G1/4 fittings and seal the unused ports with the stop plugs. For lighting, align the connector arrow with +5V on a 3-pin ARGB header.
5
Fill the loop, then run the pump with the rest of the system unpowered. Check the loop for leaks before powering the graphics card.

You also need a pump, reservoir, radiator with fans, tubing, G1/4 fittings, and coolant.

Bykski assembly drawing. 1 block · 2 thermal pads · 3 graphics card PCB · 4 washers · 5 spring screws · 6 backplate · 7 backplate screws.

FAQ

Which XFX RX 6800 XT version does this water block fit?

Bykski lists the RX 6800 XT Overseas Edition V2. Match the entire PCB to the drawing before ordering.

What fittings do I need for this block?

Use G1/4 fittings that match your tubing. Use the supplied stop plugs to seal the unused ports.

Which header powers the lighting?

Use a 5V 3-pin ARGB header and align the connector arrow with +5V. A 12V 4-pin RGB header can damage the strip.

Does the block include a backplate?

Yes. The supplied black aluminum backplate mounts behind the graphics card PCB.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item. The product does NOT come with English instructions. Please see the product gallery images for the install guide if available. Generally, thermal pads should be installed on the card where the block has corresponding raised contact points, except the GPU core, which uses thermal paste. Installing pads on other components can lead to improper contact and poor performance.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.