Huawei Atlas 300I A2 Water Block | Bykski H-ATLAS300IA2-SR (Also Fits 300T A2)

Bykski · H-ATLAS300IA2-SR

Full-cover liquid cooling for the Huawei Atlas 300I A2

The Bykski H-ATLAS300IA2-SR is a full-cover water block with an aluminum backplate for the Huawei Atlas 300I A2 inference card. It replaces the stock passive air cooler on a matching PCB. The copper cold plate transfers heat to coolant, which carries it to a radiator in your custom liquid cooling loop.

Fits
Atlas 300I A2 / Atlas 300T A2
Cold plate
T2 copper
Ports
G1/4 internal threads
Backplate
Aluminum, included

Compatibility

Bykski lists these cards for the ATLAS300IA2 PCB layout.

  • ✓Huawei Atlas 300I A2 inference card
  • ✓Huawei Atlas 300T A2 training card

Before ordering, verify the exact card model and compare its bare PCB with the board shown.

Bare PCB reference from Bykski.

Design Highlights

Bykski’s coolant flow schematic.

Coolant path through the cold plate

Coolant passes through a jet impingement section with 0.3 mm microchannels. See Thermal Pad Placement below for the MOSFET pad locations and the accelerator chip’s contact area.

Nickel-plated T2 copper cold plate

Bykski specifies a 196.85 mm copper plate and lists the thermal conductivity of the T2 copper at 401 W/(m·K).

Separate aluminum backplate

The included backplate mounts behind the PCB, opposite the water block.

Key Specifications

ModelH-ATLAS300IA2-SR
Block materialsNickel-plated T2 copper cold plate and 304 stainless steel
ColorGunmetal
Water block (L × W × T)281.67 × 106.73 × 16.00 mm
Backplate (L × W × T)266.73 × 106.76 × 5.40 mm, aluminum
Port threadsG1/4 internal threads, marked inlet and outlet
Coolant channelsUp to 50 channels with 13,911.64 mm² of wetted area
Net weight1.5 kg
Working pressure4 bar max
Block temperature range−20 to 60 °C
O-ringEPDM
Compatible fluids (block)Water, ethylene glycol, propylene glycol, fluorinated fluid, mineral oil

Bykski’s dimension drawing in millimeters. Water block above, backplate below.

Which Version Do I Need?

Check the full model name on your card. The Atlas 300I Duo and the earlier Atlas 300 have their own water block listings.

Bykski H-ATLAS300IA2-SR water block and backplateTHIS PAGE
Choose this version for a listed Atlas A2 card with a matching PCB if you have a custom loop or plan to build one.

What's in the Box

1 × full-cover water block1 × aluminum backplate5 × 1.5 mm thermal pad strips8 × 0.5 mm washers8 × M2 × 5 mm spring screws8 × M2 × 9.5 mm backplate screws

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Power off the system and remove the accelerator. Take off its stock cooler and clean the old thermal material from the chip and contact areas.
2
Cut the supplied 1.5 mm pads to size and remove the protective film. Place the pads on the shaded MOSFET areas shown in Thermal Pad Placement below. Apply a thin layer of your own GPU thermal paste to the center chip.
3
Align the block, PCB and backplate. Fit the washers and screws as shown in the assembly drawing and tighten gradually and evenly.
4
Use G1/4 fittings to connect the tubing. Follow the inlet and outlet markings on the block.
5
Leak-test the loop with the card unpowered before starting the system.

You also need a pump, reservoir, radiator and fans, tubing, G1/4 fittings, and coolant.

1 water block · 2 thermal pads · 3 your accelerator PCB · 4 washers · 5 spring screws · 6 backplate · 7 backplate screws

Thermal Pad Placement

Bykski’s placement diagram. The dark MOSFET areas around the chip take 1.5 mm thermal pads. Apply your own thermal paste to the center chip marked by the syringe.

FAQ

Will this water block fit the Huawei Atlas 300T A2?

Yes. Bykski lists the Atlas 300T A2 training card for the ATLAS300IA2 layout. Match your board to the compatibility photo before ordering.

How is the Huawei Atlas 300I A2 cooled from the factory?

It uses a passive air cooler that depends on airflow from the host system. This block replaces that cooler and transfers heat to the coolant in a custom loop.

Do I need a separate pump and radiator?

Yes. This is a standalone water block for a custom loop. Use a pump and reservoir, a radiator with fans, coolant, tubing, and G1/4 fittings.

What should I measure before installing it?

The block measures 281.67 × 106.73 × 16.00 mm. Use the dimension drawing to check space for the block and backplate, and leave room for the fittings and tubing.

Notes
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.