RTX 3090 Strix Water Block with Active Backplate | Bykski N-AS3090STRIX-TC-V3

Bykski · N-AS3090STRIX-TC-V3

Full-cover GPU water block with an active backplate

The Bykski N-AS3090STRIX-TC-V3 is a full-cover water block for a custom loop on select ASUS ROG Strix RTX 3090, 3080 Ti, and 3080 cards. Its copper cold plate cools the GPU, memory, and voltage regulators on the front. A bridge routes coolant through the active backplate to cool the rear of the board.

Fits
Listed ASUS ROG Strix PCBs
Backplate
Liquid-cooled
Ports
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Fits these ASUS ROG Strix PCB layouts with three PCIe power connectors.

  • ✓ROG-STRIX-RTX3090-24G-GAMING
  • ✓ROG-STRIX-RTX3080TI-O12G-GAMING
  • ✓ROG-STRIX-LC-RTX3080TI-12G-GAMING
  • ✓ROG-STRIX-RTX3080-10G-GAMING
  • ✓ROG-STRIX-RTX3080-O12G-GAMING

Not compatible:

  • ✗ASUS TUF Gaming PCB layouts

Before ordering, check the full ASUS model code and compare the bare PCB with Bykski’s layout for this water block. Check mounting holes, component placement, and power connector locations.

Bykski bare PCB reference for the ASUS ROG Strix RTX 3090 24GB Gaming.

Design Highlights

Coolant runs through the backplate

The bridge connects the front block to the copper waterway in the backplate. On the listed RTX 3090, the backplate draws heat from memory on the rear of the PCB.

GPU cold plate

Coolant passes through jet microchannels over the GPU die.

5V addressable RGB

Use a matching 5V 3-pin ARGB connection for the RBW lighting.

Key Specifications

ModelN-AS3090STRIX-TC-V3
Cold plateElectroplated T2 high-purity copper
Front coverClear acrylic
Active backplateElectroplated copper waterway
Port threadG1/4 inlet and outlet
Front block (L × W × T)248.68 × 158.10 × 22.65 mm
Active backplate (L × W × T)267.03 × 128.69 × 17.25 mm
Lighting5V 3-pin ARGB (RBW)

Which Version Do I Need?

Use the model code on your graphics card to choose between the Strix and TUF Gaming blocks.

N-AS3090STRIX-TC-V3THIS PAGE
Choose this active-backplate kit for a ROG Strix PCB listed above.
For an ASUS TUF Gaming card, check this active-backplate kit’s own PCB compatibility list.

What's in the Box

1 × full-cover GPU water block1 × active backplate1 × bridge2 × G1/4 stop plugs1 × mounting hardware setThermal pads5V ARGB lighting5V 3-pin ARGB adapter cable for the motherboard

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Bykski illustration of the three main components.

Installation & Use

1
Power off the system and remove the card. Take off the stock cooler and backplate, then clean off old thermal paste and pad residue.
2
Check that the mounting holes line up. Follow the installation diagram for your exact PCB and apply the supplied thermal pads to the marked memory and power components. Apply your own thermal paste to the GPU die.
3
Mount the front block with even pressure, then install the active backplate with the designated hardware.
4
Seat the bridge seals and fasten the bridge to both blocks. Tighten the screws gently.
5
Connect G1/4 fittings to the marked inlet and outlet and plug the unused ports. Use the included adapter cable to connect the lighting to a 5V 3-pin ARGB header on the motherboard. Leak-test the loop before powering the card.

You also need a pump, radiator, G1/4 tubing fittings, tubing, and coolant.

Bykski bridge assembly drawing. 1 Seals · 2 Bridge · 3 and 4 Mounting screws.

FAQ

Does this fit an ASUS ROG Strix RTX 3080 Ti?

The RTX 3080 Ti Gaming OC and the RTX 3080 Ti Strix LC 12GB models listed in Compatibility are supported. Check the full model code and PCB layout before ordering.

Can I plug the 3-pin ARGB cable into a 4-pin RGB header?

Use a 5V 3-pin ARGB connection. A 12V 4-pin RGB header can damage the lighting.

What does the active backplate cool?

Coolant flows through the backplate to remove heat from the rear of the PCB. On the listed RTX 3090, that includes the rear memory.

Which fittings and ports should I use?

Use G1/4 tubing fittings and follow the bridge’s inlet and outlet markings. Bykski illustrates a lower inlet and upper outlet, with the unused ports plugged.

Notes
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.