ASUS Dual RTX 4060 Ti OC 8GB Water Block with Backplate | Bykski N-AS4060TIDUAL-X

Bykski · N-AS4060TIDUAL-X

Full-cover water block for ASUS Dual RTX 4060 Ti OC 8GB

The Bykski N-AS4060TIDUAL-X replaces the stock cooler on a supported ASUS Dual GeForce RTX 4060 Ti OC 8GB. Its nickel-plated copper cold plate transfers heat from the GPU, memory, and voltage regulators into a custom liquid cooling loop. The kit includes a black aluminum backplate that mounts behind the card.

Fits
ASUS Dual RTX 4060 Ti OC 8GB
Cold plate
Nickel-plated copper
Ports
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Supported ASUS Dual PCB

  • ✓ASUS Dual GeForce RTX 4060 Ti OC Edition 8GB (DUAL-RTX4060TI-O8G)

Not compatible:

  • ✗ASUS Dual GeForce RTX 4060 Ti OC Edition 16GB (DUAL-RTX4060TI-O16G)

Before ordering, check your card’s model number. Compare the entire PCB and its mounting holes with the bare-board photo in the product gallery. If you’re unsure, ask us to confirm your PCB.

ASUS DUAL-RTX4060TI-O8G shown with its factory cooler for model identification.

Design Highlights

Clear acrylic top with G1/4 ports

The clear cover exposes the coolant channels. The inlet and outlet take G1/4 fittings sized for the tubing in your loop.

Jet microchannels over the GPU

Coolant passes through fine channels above the GPU contact area. The full-cover cold plate also draws heat from the memory and voltage regulators.

Black aluminum backplate

The included passive backplate mounts behind the PCB. Coolant stays in the water block.

Key Specifications

Model (SKU)N-AS4060TIDUAL-X
Cold plateNickel-plated copper
TopClear acrylic
BackplateBlack aluminum, passive
Cooling coverageGPU, memory, and VRM
Port threadG1/4 inlet and outlet
Water block (L × W × T)170.00 × 145.61 × 26.15 mm
Backplate (L × W × T)170.00 × 115.53 × 6.00 mm
Lighting5V 3-pin ARGB (RBW)

Bykski’s separate dimensions for the block (top) and backplate (bottom), in millimeters.

Which Version Do I Need?

Start with the model on your card’s label, then check the PCB listed for that block.

ASUS Dual RTX 4060 TiTHIS PAGE
Choose N-AS4060TIDUAL-X for the OC 8GB card (DUAL-RTX4060TI-O8G) once you’ve matched the PCB.
Check N-GV4060TIGMOC-X for the 8GB or 16GB Gigabyte Gaming OC card.
Check N-MS4060TIVES-X for the MSI Ventus 2X 16GB card.
Check N-MS4060VES-X for the specific MSI RTX 4060 cards it lists.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × mounting hardware set1 × thermal pad set1 × 5V ARGB light strip

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the PC, remove the card, and detach the factory cooler. Clean the old thermal material off the GPU and the components that contact the block.
2
Place the supplied thermal pads on the memory and power components indicated in Bykski’s installation diagram. Apply a thin layer of your own thermal paste to the GPU die.
3
Align the block with the PCB’s mounting holes. Fit the included backplate and tighten the mounting screws gradually and evenly.
4
Connect your tubing with G1/4 fittings and seal the unused ports with the stop plugs. To sync lighting with a motherboard, use a compatible adapter for its 5V 3-pin ARGB header.
5
Leak-test the loop while the graphics card is unpowered. Power the card only after the loop passes the test.

For the loop, supply a pump, reservoir, radiator, coolant, tubing, and G1/4 fittings that match your tubing.

Bykski assembly diagram. 1 Block · 2 Thermal pads · 3 Graphics card PCB · 4 Washers · 5 Spring screws · 6 Backplate · 7 Backplate screws.

FAQ

Is the ASUS Dual RTX 4060 on the fit list?

Bykski’s fit list does not include the ASUS Dual RTX 4060 OC 8GB (DUAL-RTX4060-O8G). Choose a block that lists your full card model and matches its PCB.

Does the block include a backplate?

Yes. It includes a passive black aluminum backplate that mounts behind the PCB.

Which fittings should I use?

Use G1/4 fittings sized for your tubing and close unused ports with the included stop plugs.

Which RGB header powers the lighting?

Use a compatible adapter for a 5V 3-pin ARGB motherboard header, or connect the lighting to a compatible 5V ARGB controller. A 12V 4-pin RGB header can damage the LEDs.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.