ASUS TUF RTX 4090 OG OC & ROG Strix LC RTX 4090 Water Block with Backplate | Bykski N-AS4090TUFOG-X

Bykski · N-AS4090TUFOG-X

Full-cover GPU water block for ASUS TUF RTX 4090 OG OC and ROG Strix LC

The Bykski N-AS4090TUFOG-X replaces the stock cooler on supported cards such as the ASUS TUF Gaming GeForce RTX 4090 OG OC. Its nickel-plated copper cold plate transfers heat from the GPU die, memory, and voltage regulators to a custom liquid cooling loop. The block includes an aluminum backplate and uses 5V addressable RGB.

Fits
Select ASUS TUF OG OC and ROG Strix LC cards
Cold plate
Nickel-plated T2 copper
Ports
G1/4
Lighting
5V 3-pin ARGB

Compatibility

Check your ASUS card’s full model number.

  • ✓ASUS TUF Gaming GeForce RTX 4090 24GB OG OC Edition (TUF-RTX4090-O24G-OG-GAMING)
  • ✓ASUS ROG Strix LC GeForce RTX 4090 24GB (ROG-STRIX-LC-RTX4090-24G-GAMING)
  • ✓ASUS TUF Gaming GeForce RTX 4070 Ti SUPER 16GB OG OC Edition (TUF-RTX4070TIS-O16G-OG-GAMING)

Not compatible:

  • ✗ASUS TUF Gaming GeForce RTX 4090 (non-OG)
  • ✗ASUS ROG Strix GeForce RTX 4090 (air-cooled)

Before ordering, check the exact model on your card label and verify the PCB layout with FormulaMod if you are unsure.

Bykski’s ASUS RTX 4090 PCB reference photo.

Design Highlights

Bykski coolant flow illustration.

Full-cover cooling

The cold plate draws heat from the GPU die, memory, and voltage regulators. Coolant carries that heat to the radiator in your loop.

Jet microchannels

Coolant passes through fine channels machined into the cold plate over the GPU die.

Clear acrylic top and ports on both sides

The clear top exposes the channels. The G1/4 terminal provides connections on both sides, so you can route the tubing from the side that fits your build.

Key Specifications

ModelN-AS4090TUFOG-X
Cold plateNickel-plated T2 copper
TopClear acrylic (PMMA)
BackplateBlack aluminum backplate, outside the coolant path
Cooling coverageGPU die, memory, and VRM
Port threadG1/4
Lighting5V 3-pin addressable RGB (RBW)
Water block (L × W × T)267.90 × 157.25 × 30.19 mm
Backplate (L × W × T)266.95 × 135.47 × 6.00 mm

Bykski dimension drawing. Measurements are in millimeters.

Which Version Do I Need?

Compare the top material and lighting, then check the PCB list for the model you choose.

Bykski N-AS4090TUFOG-XTHIS PAGE
Choose this version for a clear acrylic top and 5V 3-pin ARGB.
Choose this version for a stainless steel panel and POM construction with no lighting.

What's in the Box

1 × GPU water block1 × aluminum backplate2 × G1/4 stop plugs1 × mounting hardware set1 × thermal pad set

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the PC, remove the graphics card, and take off its stock cooler. Clean off the old thermal materials.
2
Use the supplied thermal pads on the memory and power components shown in the installation guide for your exact PCB. Apply your own thermal paste to the GPU die.
3
Line up the mounting holes, fit the block and backplate, and tighten the mounting screws evenly. Stop if parts do not line up.
4
Connect the loop with G1/4 fittings and close the unused ports with the supplied plugs. For lighting, use a compatible cable to connect the block to a 5V 3-pin ARGB header.
5
Leak-test the filled loop with the graphics card unpowered before starting the PC.

You also need a pump, radiator, G1/4 fittings, tubing, and coolant.

① Block · ② Thermal pads · ③ Your GPU PCB · ④ Washers · ⑤ Spring screws · ⑥ Backplate · ⑦ Backplate screws

FAQ

Which ASUS TUF RTX 4090 does this water block fit?

Check for TUF-RTX4090-O24G-OG-GAMING on the card label and confirm the PCB against the compatibility reference before ordering.

Does it fit an air-cooled ROG Strix RTX 4090?

This block fits the ROG Strix LC 24GB model listed above. The air-cooled Strix uses a different block.

Does the block include a backplate?

Yes. The included black aluminum backplate mounts behind the graphics card PCB, outside the coolant path.

Which fittings do I need?

Use G1/4 fittings matched to your tubing and close unused ports with the included stop plugs.

Can I plug the lighting into a 12V RGB header?

Use a 5V 3-pin ARGB header. Connecting the lighting to 12V RGB can damage it.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.