Bykski · N-AS5070TIBTF-X
Full-cover water block for the ASUS TUF RTX 5070 Ti BTF
The Bykski N-AS5070TIBTF-X replaces the stock cooler on the ASUS TUF Gaming GeForce RTX 5070 Ti BTF White OC Edition so you can connect the card to a custom liquid cooling loop. The copper cold plate cools the GPU core, memory, and voltage regulators. A black aluminum backplate mounts behind the card.
Fits
ASUS TUF 5070 Ti BTF White OC
Compatibility
Bykski lists one compatible ASUS PCB layout.
- ✓ASUS TUF Gaming GeForce RTX 5070 Ti BTF White OC Edition (TUF-RTX5070TI-O16G-BTF-WHITE)
Before ordering, check the exact model number on your card and compare its PCB with Bykski’s board illustration in Installation & Use.
ASUS reference photo of the compatible graphics card with its original cooler.
Design Highlights
One cold plate for the core, memory, and VRM
The raised contact surfaces line up with the heat-producing components on the ASUS PCB. Coolant passes through 0.3 mm microchannels in the copper cold plate.
Black aluminum backplate
The included backplate fastens behind the PCB. Coolant circulates through the front block.
5V addressable lighting
The clear top shows the coolant channels and the built-in ARGB lighting. Use a compatible 5V 3-pin ARGB connection.
Key Specifications
| Bykski model | N-AS5070TIBTF-X |
|---|
| Cooling coverage | GPU core, memory, and VRM |
|---|
| Cold plate | T2 copper |
|---|
| Top | Clear |
|---|
| Backplate | Black aluminum, passive |
|---|
| Port thread | G1/4 inlet and outlet |
|---|
| Water block (L × W × T) | 239.96 × 158.16 × 25.69 mm |
|---|
| Backplate (L × W × T) | 239.90 × 127.28 × 5.94 mm |
|---|
| Lighting | 5V 3-pin addressable RGB (RBW) |
|---|
Bykski dimension drawing in millimeters. The water block is above the backplate.
Which Version Do I Need?
Start with the graphics card model on its label.
Bykski N-AS5070TIBTF-XTHIS PAGE
Choose this block for the ASUS TUF RTX 5070 Ti BTF White OC PCB above.
Choose this block for the ASUS PRIME GeForce RTX 5070 12GB or 12GB OC.
What's in the Box
1 × full-cover GPU water block1 × black aluminum backplate2 × G1/4 stop plugsThermal padsMounting hardware set
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Bykski assembly drawing. 1 water block · 2 thermal pads · 3 your graphics card PCB · 4 gaskets · 5 spring screws · 6 backplate · 7 backplate screws.
Installation & Use
1Turn off the PC, remove the graphics card, and take off its stock cooler. Clean the old thermal material from the GPU and surrounding components.
2Cut the supplied thermal pads to fit the areas shown in the diagram. Remove the protective film and spread a thin layer of your own thermal paste on the GPU die.
3Align the block with the PCB without forcing it. Use the assembly drawing above to position the gaskets, spring screws, backplate, and backplate screws. Tighten the screws gradually.
4Connect the tubing using G1/4 fittings. Follow the inlet and outlet markings by the ports.
5Leak-test the loop with the graphics card unpowered before starting the PC.
Use a pump, radiator, coolant, tubing, and matching G1/4 fittings. An optional reservoir or pump/reservoir combo makes filling and bleeding easier.
Bykski’s PCB illustration. The dark strips mark pad locations on the memory and VRM. The applicator marks the GPU die.
FAQ
Which RTX 5070 Ti can I use with this block?
Match the ASUS TUF Gaming BTF White OC card number TUF-RTX5070TI-O16G-BTF-WHITE, then check the PCB layout.
What do I need to water-cool this card?
Use this block in a custom loop with a pump, radiator, coolant, tubing, and matching G1/4 fittings. A reservoir is optional.
Does coolant flow through the included backplate?
The black aluminum backplate is passive. The coolant flows through the water block on the front of the card.
Which lighting header should I use?
Use a 5V 3-pin ARGB header or compatible 5V ARGB controller. A 12V 4-pin RGB header can damage the lighting.
Which fittings match the water block?
Use G1/4 fittings on the inlet and outlet. Match the tubing side of each fitting to your chosen tubing.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.