Gigabyte RTX 4060 Ti Gaming OC 8G/16G Water Block with Backplate — Bykski N-GV4060TIGMOC-X

Bykski · N-GV4060TIGMOC-X

Full-cover water block for Gigabyte RTX 4060 Ti Gaming OC

The Bykski N-GV4060TIGMOC-X replaces the stock cooler on supported Gigabyte GeForce RTX 4060 Ti Gaming OC cards so they can run in a custom liquid cooling loop. Its T2 copper cold plate draws heat from the GPU, memory, and voltage regulators. A matching aluminum backplate and 5V addressable lighting are included.

Fits
Gaming OC 8G / 16G
Port thread
G1/4
Lighting
5V 3-pin ARGB
Backplate
Black aluminum

Compatibility

Bykski lists these two Gigabyte Gaming OC models.

  • ✓Gigabyte GeForce RTX 4060 Ti Gaming OC 8G
    GV-N406TGAMING OC-8GD
  • ✓Gigabyte GeForce RTX 4060 Ti Gaming OC 16G
    GV-N406TGAMING OC-16GD

Before ordering, verify your exact card model and compare its PCB layout with the board photo in the product gallery.

Gigabyte Gaming OC 16G shown with its original cooler.

Design Highlights

Full-cover cold plate under clear acrylic

The T2 copper cold plate spans the GPU, memory, and power delivery components. The clear acrylic top lets you see the coolant path and the marked inlet and outlet.

Jet microchannels over the GPU

Coolant passes between fins with 0.3 mm gaps over the GPU core. The fins provide more surface area for heat to transfer to the coolant.

5V addressable lighting

The included strip lights the clear top. Use the sync cable with a 5V 3-pin ARGB motherboard header.

Key Specifications

ModelN-GV4060TIGMOC-X
Cooling coverageGPU core, memory, and VRM
Cold plateT2 copper
TopClear acrylic
BackplateBlack aluminum
Port threadG1/4 inlet and outlet
Jet microchannel gap0.3 mm
Lighting connector5V 3-pin ARGB (RBW)
Water block (L × W × T)173.60 × 135.50 × 26.45 mm
Backplate (L × W × T)173.61 × 105.50 × 6.00 mm

Bykski dimension drawing in millimeters. Water block above, backplate below.

Which Version Do I Need?

If your card is from ASUS or MSI, match its exact model to the corresponding water block.

Bykski N-GV4060TIGMOC-XTHIS PAGE
For the Gigabyte Gaming OC 8G and 16G boards listed above.
For the ASUS Dual GeForce RTX 4060 Ti OC 8GB.
For the MSI GeForce RTX 4060 Ti Ventus 2X 16GB.

What's in the Box

1 × full-cover GPU water block1 × aluminum backplate2 × G1/4 stop plugsThermal pad setMounting hardware set1 × 5V ARGB LED strip1 × lighting sync cable

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Power off the PC and remove the graphics card. Take off the stock cooler and backplate, then clean off the old thermal paste and pad residue.
2
Cut the pads to fit the memory and power delivery contact points shown in Bykski’s instructions. Apply a thin layer of your own thermal paste to the GPU die.
3
Line up the block and PCB. Fit the washers, spring screws, and backplate in the order shown. Tighten the mounting screws gradually and evenly.
4
Connect the G1/4 tubing fittings to the marked inlet and outlet. Close the unused ports with the included stop plugs.
5
For lighting, align the sync cable arrow with the +5V pin on the motherboard’s 3-pin ARGB header.
6
Leak-test the loop before powering the graphics card.

For the custom loop, you also need a pump and reservoir, radiator and fans, tubing with matching G1/4 fittings, and coolant.

Bykski installation diagram. 1 Water block · 2 Thermal pads · 3 Your graphics card PCB · 4 Washers · 5 Spring screws · 6 Backplate · 7 Backplate screws.

FAQ

Does this water block fit the RTX 4060?

It fits the two Gigabyte GeForce RTX 4060 Ti Gaming OC boards listed above. The GeForce RTX 4060 without the Ti suffix is outside that fit list.

Will it fit both Gigabyte Gaming OC memory capacities?

Yes. Bykski lists the 8G and 16G Gaming OC models. Verify your exact card number and PCB layout before ordering.

What are the water block and backplate made of?

The water block has a T2 copper cold plate and a clear acrylic top. The included backplate is black aluminum.

Can I use a 12V RGB header for the lighting?

Use a 5V 3-pin addressable RGB header. Connecting the strip to a 12V 4-pin RGB header can damage it.

Which fittings do I need?

Use G1/4 fittings sized for your tubing. Follow the inlet and outlet markings on the block and plug the unused ports.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.