Bykski · N-GY3060XJ-X
Full-cover GPU water block for select RTX 3060 Ti and RTX 3060 cards
The Bykski N-GY3060XJ-X replaces the stock cooler on supported GeForce RTX 3060 Ti and RTX 3060 boards, including the Palit RTX 3060 Dual 12GB. Its copper cold plate transfers heat from the GPU core, memory, and voltage regulators into a custom liquid cooling loop.
Fits
Select RTX 3060 Ti and RTX 3060 PCBs
Compatibility
Bykski identifies these board layouts for the N-GY3060XJ-X.
- ✓GALAX GeForce RTX 3060 Xiaojiang
- ✓GALAX GeForce RTX 3060 Ti Xiaojiang
- ✓Palit GeForce RTX 3060 Dual OC 12GB (NE63060T19K9-190AD)
- ✓Palit GeForce RTX 3060 Dual 12GB
- ✓Palit GeForce RTX 3060 Ti Dual 8GB
- ✓Gainward GeForce RTX 3060 Ti Ghost 8GB
- ✓Gainward GeForce RTX 3060 Ti 8G G3 LHR (RTX3060TI-8G-G3-LHR)
- ✓Manli GeForce RTX 3060 12GB LHR
- ✓Inno3D GeForce RTX 3060 Ti Black Gold Supreme
- ✓Yeston GeForce RTX 3060 Ti 8G D6 Liudao Bingjia
Not compatible:
- ✗NVIDIA GeForce RTX 3060 Ti Founders Edition
Before ordering, verify your exact card model and PCB revision. Compare the full board, mounting holes, and component positions with the matching manufacturer layout.
Palit’s GeForce RTX 3060 Dual OC with its factory cooler. Check the exact card model and PCB before ordering.
Design Highlights
Cold plate for the GPU, memory, and VRM
The cold plate contacts the GPU core and uses thermal pads at the corresponding memory and voltage regulator contact points. Coolant passes through the microchannels above the core.
Clear acrylic top with G1/4 ports
The clear top exposes the coolant path. Follow the inlet and outlet markings on the block near the ports when connecting it to your loop.
Key Specifications
| Model | Bykski N-GY3060XJ-X |
|---|
| Order code | N-GY3060XJ-X_RBW |
|---|
| Cold plate | Copper cold plate |
|---|
| Top | Clear acrylic |
|---|
| Coolant port thread | G1/4 |
|---|
| Block (L × W × T) | 144.76 × 128.39 × 26.56 mm |
|---|
| Backplate (L × W × T) | 144.76 × 98.39 × 6 mm |
|---|
| Backplate material | Black aluminum |
|---|
| Lighting | 5V 3-pin addressable RGB (RBW) |
|---|
Bykski dimension drawing in millimeters. Water block above, backplate below.
Which Version Do I Need?
Choose the water block by the graphics card’s exact PCB.
Bykski N-GY3060XJ-XTHIS PAGE
Choose this block when your card matches one of the PCB layouts above.
Check this block for a Gigabyte AORUS GeForce RTX 3060 Elite 12G with two PCIe power connectors. Compare your exact PCB revision with the product listing.
What's in the Box
1 × full-cover GPU water block1 × black aluminum backplate2 × G1/4 stop plugs1 × 5V ARGB light stripThermal padsMounting hardware set
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
1Power off the system, remove the card, and lift off the stock cooler. Clean the old thermal paste and pad residue. Check that the block lines up with the PCB and screw holes.
2Fit thermal pads to the corresponding memory and VRM contact points. Apply a thin layer of your own thermal paste to the GPU die.
3Align the block, your graphics card, and the included backplate. Place the insulating washers and screws as shown. Tighten the spring screws gradually in a cross pattern, then secure the backplate.
4Connect your loop tubing through G1/4 fittings at the marked inlet and outlet. Seal unused ports with stop plugs.
5For lighting, use a compatible 5V 3-pin ARGB adapter cable to connect the strip to a 5V ARGB motherboard header, or use a compatible 5V ARGB controller. Leak-test the loop with the card unpowered before starting the system.
You also need a pump, radiator, tubing, matching G1/4 tube fittings, and coolant.
Bykski installation drawing. 1 water block · 2 thermal pads · 3 your graphics card PCB · 4 insulating washers · 5 spring screws · 6 backplate · 7 backplate screws.
FAQ
Will this fit my RTX 3060 Ti or RTX 3060?
Check the complete graphics card model and PCB revision against the compatibility list before ordering. Board layouts vary within each GPU family.
Does it fit the Gainward RTX 3060 Ti Ghost?
The Gainward GeForce RTX 3060 Ti Ghost 8GB is listed. Check the full PCB and mounting holes before ordering.
What fittings does the block take?
Use G1/4 fittings sized for your tubing. Use the included stop plugs to seal the unused ports.
Can I plug the lighting into a 12V RGB header?
A 12V RGB header can damage the light strip. Use a compatible 5V 3-pin ARGB adapter cable for a 5V ARGB motherboard header, or connect the strip to a compatible 5V ARGB controller.
What else do I need to water-cool the card?
You need a custom loop with a pump, radiator, tubing, matching G1/4 fittings, and coolant.
Notes- This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
- This product is designed for self-installation. The manufacturer is not liable for any damages resulting from misuse, including, but not limited to, improper installation or the use of incompatible hardware or fluids. By using this product, you accept all related risks.