Bykski · N-MS4090VES-X
Full-cover water block for the MSI RTX 4090 Ventus 3X 24G OC
The Bykski N-MS4090VES-X is a full-cover GPU water block for the MSI GeForce RTX 4090 Ventus 3X 24G OC. It replaces the stock air cooler to cool the GPU core, memory, and voltage regulators in a custom liquid-cooling loop. The included aluminum backplate mounts behind the card, and G1/4 ports connect the block to the loop.
Fits
MSI RTX 4090 Ventus 3X 24G OC
Cold plate
Nickel-plated T2 copper
Compatibility
Bykski lists this card and its pictured PCB layout.
- ✓MSI GeForce RTX 4090 Ventus 3X 24G OC
Before ordering, confirm the full card name and compare your PCB with the full bare-board photo in the product gallery.
MSI’s product image with the stock air cooler fitted.
Design Highlights
Direct contact across the board
The nickel-plated copper plate contacts the GPU core, memory, and voltage regulators through their thermal interfaces. Coolant flows through jet microchannels in the cold plate.
Visible channels and marked ports
The clear acrylic top exposes the coolant channels. Follow the IN and OUT markings on the front of the block when connecting your fittings.
5V addressable lighting
Bykski calls its addressable lighting RBW. Use the sync cable to connect the strip to a 5V 3-pin ARGB motherboard header.
Key Specifications
| Model (SKU) | N-MS4090VES-X |
|---|
| Cold plate | Nickel-plated T2 copper |
|---|
| Top | Clear acrylic |
|---|
| Backplate | Black aluminum, passive |
|---|
| Cooling coverage | GPU core, memory, and VRM |
|---|
| Inlet and outlet thread | G1/4 |
|---|
| Block (L × W × T) | 239.85 × 160.49 × 26.15 mm |
|---|
| Backplate (L × W × T) | 239.81 × 130.50 × 6.00 mm |
|---|
| Lighting connector | 5V 3-pin ARGB (RBW) |
|---|
Bykski dimensions in millimeters. Water block above, backplate below.
Which Version Do I Need?
These blocks fit the listed Ventus 3X 24G OC layout. Choose the top and backplate design you prefer.
Bykski N-MS4090VES-XTHIS PAGE
Choose this version for a clear acrylic top that shows the coolant channels and a black aluminum backplate.
Choose the Full Armor version for aluminum panels on both the front and the back.
What's in the Box
1 × full-cover GPU water block with 5V ARGB strip1 × aluminum backplate2 × G1/4 stop plugsThermal pad setMounting hardware set1 × lighting sync cable
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
1 Water block · 2 Thermal pads · 3 Your graphics card PCB · 4 Washers · 5 Spring screws · 6 Backplate · 7 Backplate screws.
Installation & Use
1Turn off and disconnect the PC. Remove the graphics card, take off its stock cooler, and clean off the old thermal material.
2Cut the included thermal pads to fit the memory and power components shown in the pad placement diagram. Apply your own thermal paste to the GPU die.
3Align the block, PCB, and backplate. Mount them with the washers and screws in the positions shown in Bykski’s assembly drawing.
4Connect your loop to the marked inlet and outlet with G1/4 fittings. Seal the unused ports with the stop plugs.
5Connect the lighting sync cable to a 5V 3-pin ARGB header, aligning the arrow with the 5V pin.
6Leak-test the loop before powering the graphics card.
You also need G1/4 fittings for your tubing, a pump, a radiator, tubing, and coolant.
Bykski’s placement diagram. The applicator marks the GPU die for paste. The other shaded areas show where the pads go.
FAQ
Which MSI RTX 4090 Ventus does this block fit?
Bykski lists the MSI GeForce RTX 4090 Ventus 3X 24G OC. Match your card’s PCB to the bare-board photo in the gallery before ordering.
What size fittings do I need?
Use G1/4 fittings sized for your tubing. Seal any unused terminal ports with the included stop plugs.
Can I plug the lighting into a 12V RGB header?
Use a 5V 3-pin ARGB header for the RBW lighting. A 12V 4-pin RGB header is incompatible and can damage the LEDs.
Does the included backplate need its own coolant lines?
The block handles coolant flow. The included passive aluminum backplate mounts behind the PCB.
Where do the thermal pads go?
Place the pads on the memory chips and the power components marked in the pad placement diagram.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.