PNY RTX 4090 XLR8 VERTO OC Water Block with Backplate | Bykski N-PNY4090-X

$146.41 piece
items available
View Details
Bykski · N-PNY4090-X

Full-cover water block for the PNY RTX 4090 XLR8 OC

The Bykski N-PNY4090-X replaces the stock air cooler on the PNY GeForce RTX 4090 24GB XLR8 Gaming VERTO EPIC-X RGB OC. It connects to a custom liquid cooling loop and cools the GPU core, memory, and voltage regulators through one nickel-plated copper cold plate. A separate black aluminum backplate mounts behind the card.

Fits
PNY RTX 4090 XLR8 OC
Ports
G1/4 inlet and outlet
Lighting
5V 3-pin ARGB
Backplate
Black aluminum

Compatibility

Bykski lists this graphics card PCB for the N-PNY4090-X.

  • ✓PNY GeForce RTX 4090 24GB XLR8 Gaming VERTO EPIC-X RGB OC Triple Fan (VCG409024TFXXPB1-O)

Before ordering, check the part number on your card and compare the entire PCB with the photo here. Check the mounting holes, connectors, and component layout.

Component side of the PNY RTX 4090 XLR8 OC PCB. Photo by Jisaku Hibi.

Design Highlights

One cold plate for the GPU, memory, and VRM

The raised surfaces on the copper cold plate line up with the GPU core, memory, and power stages. Thermal pads bridge the gap to the memory and power stages.

0.5 mm jet microchannels

Coolant flows through a bank of finely spaced fins over the GPU core. Bykski specifies a 0.5 mm gap between the fins.

5V addressable lighting

Use the lighting sync cable with a 5V 3-pin addressable RGB header. Bykski calls this connection RBW.

Key Specifications

ModelN-PNY4090-X
Cold plate9 mm T2 high-purity copper, nickel plated
TopClear acrylic
BackplateBlack aluminum, outside the coolant path
Backplate (L × H × T)213.36 × 120.00 × 6.00 mm
Microchannel gap0.5 mm
Port threadG1/4
Lighting connector5V 3-pin ARGB (RBW)

Bykski’s backplate drawing. Dimensions are in millimeters.

Which Version Do I Need?

Match the block to the exact PNY card model and PCB.

N-PNY4090-XTHIS PAGE
Choose this water block for the listed PNY RTX 4090 XLR8 Gaming VERTO OC PCB.
Check this block if your card is the PNY RTX 4080 16GB XLR8 Gaming VERTO EPIC-X RGB OC.
Check this block if your card is the PNY RTX 4070 12GB Gaming VERTO.

What's in the Box

1 × full-cover GPU water block1 × black aluminum backplate5 × 1.5 mm thermal pad strips4 × 0.5 mm insulating washers4 × spring screws5 × backplate screws2 × M3 × 6 mm bracket screws2× G1/4 stop plugsLighting sync cable

Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.

Installation & Use

1
Shut down and unplug the PC. Remove the graphics card and its stock cooler, then clean away the old thermal paste and pad residue.
2
Check that the block’s mounting holes and contact points line up with the PCB. Apply the supplied thermal pads to the memory and power stages shown in the diagram. Leave the inductors uncovered and apply your own thermal paste to the GPU die.
3
Align the block, PCB, and backplate. Install the washers and screws in their matching locations and tighten the GPU mounting screws evenly.
4
Connect the tubing with G1/4 fittings, following the IN and OUT marks on the block. Close the unused ports with stop plugs.
5
For lighting, connect the sync cable to a 5V 3-pin ARGB header and align the connector with the 5V pin.
6
Leak-test the assembled loop with the graphics card unpowered before you start the PC.

You also need a pump, reservoir, radiator, G1/4 fittings matched to your tubing, tubing, and coolant.

Bykski’s installation drawing. The shaded areas around the center mark the pad locations. Apply paste to the GPU die in the center.

FAQ

Which PNY RTX 4090 does this water block fit?

Bykski lists the XLR8 Gaming VERTO EPIC-X RGB OC Triple Fan (VCG409024TFXXPB1-O). Compare your card’s PCB with the bare-board photo in the Compatibility section before ordering.

Does this water block include an active backplate?

It includes a passive black aluminum backplate. Coolant flows through the front block only.

What fittings do I need?

Use G1/4 fittings sized for your tubing. Follow the IN and OUT marks on the block and plug unused ports.

Can I plug the lighting into a 12V RGB header?

Use a 5V 3-pin ARGB header. A 12V 4-pin RGB header can damage the lighting.

Notes
  • This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
  • The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
  • Not responsible for any damage caused by or when using this product. Please use it at your own risk.
  • The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.