Bykski · N-PNY5090-SR
Full-cover water block for the PNY RTX 5090
The Bykski N-PNY5090-SR replaces the stock cooler on the PNY GeForce RTX 5090 32GB GDDR7 with the PCB layout shown below. Connect it to a custom liquid cooling loop to cool the GPU core, memory, and power delivery components with one block. The included aluminum backplate mounts behind the card.
Fits
PNY RTX 5090 32GB GDDR7 · Match the PCB photo
Ports
G1/4 inlet and outlet
Compatibility
Bykski specifies the PNY board layout shown here.
- ✓PNY GeForce RTX 5090 32GB GDDR7 with the PCB layout shown
Before ordering, check your exact card model and compare its PCB shape, mounting holes, and component positions with the photo. If you have a different layout or cannot verify it, ask for a fit check before ordering.
Bare PNY RTX 5090 PCB shown by Bykski for this block.
Design Highlights
One cold plate for the GPU, memory, and VRM
The T2 copper cold plate picks up heat from the GPU die, memory, and voltage regulators. Raised contact surfaces line up with the components shown in the installation diagram.
0.3 mm jet microchannels
Coolant passes through the fine channels machined into the cold plate above the GPU.
Stainless steel panel with end ports
The block is 17 mm thick. Check the dimension drawing when planning room for fittings and tubing at the end of the card.
Key Specifications
| Model (SKU) | N-PNY5090-SR |
|---|
| Cold plate | T2 copper |
|---|
| Panel | 304 stainless steel |
|---|
| Backplate | Black aluminum, passive |
|---|
| Port thread | G1/4 female inlet and outlet |
|---|
| Block (L × W × T) | 233.66 × 121.62 × 17.00 mm |
|---|
| Backplate (L × W × T) | 215.07 × 119.54 × 3.96 mm |
|---|
| Microchannel width | 0.3 mm |
|---|
| Seal material | EPDM |
|---|
| Net weight | 1.7 kg |
|---|
| Working temperature | −20 to 60°C |
|---|
| Block color | Titanium gray |
|---|
Bykski’s dimension drawing in millimeters. Water block above, backplate below.
Which Version Do I Need?
Bykski N-PNY5090-SRTHIS PAGE
Choose this model for a custom loop if you want the stainless steel panel and your PCB matches the one above.
Compare this clear-top block if you want to see the coolant path in your custom loop. Check the PCB on its listing.
Compare this all-in-one kit if you want a block already connected to a radiator. Check its own compatibility list and radiator clearance.
What's in the Box
1 × full-cover GPU water block1 × aluminum backplateThermal pad setMounting hardware set
Thermal paste is not included (it cannot be shipped by air). Please use your own thermal paste during installation.
Installation & Use
1Shut down and unplug the system. Remove the graphics card, its stock cooler, and the old thermal materials.
2Fit the supplied thermal pads to the memory and VRM areas shown. Apply your own thermal paste to the GPU die.
3Check that you have the mounting hardware specified for the N-PNY5090-SR. Slip the spacers over the screw posts and align the block with the PCB mounting holes. Stop and contact support if the holes are out of alignment or the block cannot sit flush.
4Set the backplate behind the PCB. Place the insulating washers at the corresponding holes on the back of the PCB and tighten the spring screws. Then use the backplate screws only in their designated holes.
5Use G1/4 fittings to connect the marked inlet and outlet to your loop. Leak-test the loop before powering the graphics card.
You’ll also need a pump, radiator, G1/4 fittings sized for your tubing, tubing, and coolant.
Bykski’s installation drawing. Use thermal pads on the shaded memory and VRM areas and thermal paste on the central GPU die.
FAQ
How do I check if this water block fits my PNY RTX 5090?
Check your exact model and compare the board to Bykski’s PCB photo. Match the board outline, mounting holes, and component layout before ordering.
Which fittings do I need?
Both ports use G1/4 female threads. Choose G1/4 fittings that suit your loop’s tubing.
Does the included backplate connect to the liquid loop?
The aluminum backplate is passive. Connect your loop to the front water block.
Which thermal pads go between the card and the block?
Fit the supplied thermal pads to the memory and VRM areas shown. Apply your own thermal paste to the GPU die.
Notes- This is a repair or replacement-only item. Returns are not accepted in principle on compatibility issues or if the block has had water/fluid run through it.
- The manufacturer reserves the right to alter the block design to expand compatibility or upgrade/modify the product. The delivered item may not 100% match the pictured item.
- Not responsible for any damage caused by or when using this product. Please use it at your own risk.
- A 36-month warranty is listed.
- The copper plate of the block is processed by CNC machines. The machining marks and slightly uneven on the copper plate are normal and do not affect the use of the block. Please pay attention to this.