NVIDIA A100 40GB PCIe Water Block with Backplate – Bykski N-TESLA-A100-40G-SR

Bykski · N-TESLA-A100-40G-SR

A100 40GB PCIe water block for a custom loop

The Bykski N-TESLA-A100-40G-SR is a full-cover GPU water block with a backplate for the NVIDIA A100 40GB PCIe. It replaces the card’s passive heatsink and transfers heat from the GPU, memory, and power stages to a radiator in your custom liquid-cooling loop.

Fits
NVIDIA A100 40GB PCIe
Cold plate
Copper
Loop type
Custom liquid cooling

Compatibility

Supported PCIe board layouts

  • ✓NVIDIA A100 40GB PCIe
  • ✓NVIDIA CMP 170HX 8GB PCIe
  • ✓NVIDIA A30 24GB PCIe

Match the mounting holes, components, and power connector on your exact PCB before ordering.

Bare NVIDIA A100 40GB PCIe board. Compare the mounting holes and power connector with your card.

Design Highlights

Blue indicates the inlet side in this flow diagram.

Cool the GPU, memory, and power stages

The copper cold plate collects heat from the GPU, its memory, and the board’s power stages. Coolant enters through the marked inlet and carries that heat to the radiator.

Backplate fits behind the board

The separate backplate attaches to the rear of the PCB after the cold plate is in place.

Key Specifications

ModelN-TESLA-A100-40G-SR
Cooler typeFull-cover GPU water block for a custom loop
Cold plateCopper
Cooling coverageGPU, memory, and power stages
BackplateIncluded
Flow directionFollow the IN and OUT markings on the block

Which Version Do I Need?

Start with your card’s PCB, then choose a stand-alone block or an all-in-one kit.

N-TESLA-A100-40G-SRTHIS PAGE
Choose this block and backplate for a matching PCB when you’re building or using a custom loop.
Choose the single-card 360 mm option if you want the pump and radiator in one kit and your case has room for the radiator and fans.
This earlier stand-alone block has its own fit guide. Check it if you’re replacing an X-V2.
Compare this stand-alone block if you want an alternate design for your custom loop. Use its own PCB fit guide.
Check this separate block’s compatibility list for the A100 or A800 80GB.

What's in the Box

1 × GPU water block1 × backplate

Thermal paste is not included (it cannot be shipped by air). Please use your own GPU thermal paste during installation.

Installation & Use

1
Shut down and unplug the system. Remove the GPU and its stock cooler, then clean the contact surfaces.
2
Peel the protective film from both sides of each thermal pad, then place the pads at the board’s matching contact points. Apply a thin layer of GPU thermal paste to the GPU’s contact surface.
3
Set the block down evenly so the pads stay aligned. Tighten opposite mounting screws a little at a time, then attach the backplate.
4
Route the tubing to the marked inlet and outlet. Fill and bleed the loop.
5
Power only the pump during the leak test. Power the card once the loop is circulating and all connections are dry.

You also need a pump, reservoir, radiator and fans, tubing, compatible fittings, and coolant. Confirm the required pad thickness for your block revision and PCB before mounting.

Assembly diagram · 1 Water block · 2 Thermal pads · 3 PCB · 4 Washers · 5 Spring screws · 6 Backplate · 7 Backplate screws

FAQ

Does it fit the A100 80GB or A100 SXM?

The 40G-SR is specified for the A100 40GB PCIe. The SXM module uses a different form factor, and Bykski lists a separate 80GB block.

Which CMP 170HX fits?

The published compatibility list specifies the 8GB PCIe card. Compare your PCB and mounting holes before ordering.

Will this fit a Tesla V100?

The 40G-SR fit list is limited to the three boards above. Choose a block for your exact Tesla V100 PCB.

Is this the Bykski N-TESLA-A100-X-V2?

This page is for the N-TESLA-A100-40G-SR. The earlier X-V2 has its own PCB fit guide. Match your card to the guide for the exact block model before ordering.

Do I need a separate pump?

Use your existing loop pump or add one when building a new loop. The pump circulates coolant through the block and radiator.

What should I check for case clearance?

Check the space around the card for the fitted block, its fittings, and the tubing bends. Check your case’s radiator mount for room for the radiator and its fans.

Notes
  • This is a repair or replacement-only item. Returns are not accepted on compatibility issues or if the block has had water/fluid run through it.
  • See the installation diagram above.
  • The manufacturer reserves the right to alter the block design to expand compatibility. The delivered item may not 100% match the pictured item.
  • This product is designed for self-installation. The manufacturer is not liable for any damages resulting from misuse, including, but not limited to, improper installation or the use of incompatible hardware or fluids. By using this product, you accept all related risks.