Bykski · B-CEC-X
ATX open-frame case for a custom loop
The Bykski B-CEC-X is a black aluminum open-frame PC case for custom liquid cooling builds with an ATX motherboard. Its integrated acrylic distribution plate gives you a place to connect your tubing while leaving the loop visible. Set the chassis upright for display or lay it flat on a workbench.
Fits
ATX / Micro-ATX / Mini-ITX
Radiator mounts
2 × 360 mm
Compatibility
Check your motherboard and cooling hardware against these fit limits.
- ✓Mini-ITX motherboard (170 × 170 mm)
- ✓Micro-ATX motherboard (244 × 244 mm)
- ✓ATX motherboard (305 × 244 mm)
- ✓Two 360 mm radiators, each up to 31.6 mm thick
- ✓Up to six 120 mm fans, each up to 28 mm thick
- ✓One ATX power supply up to 220 mm long
Before ordering, compare the actual dimensions of your radiator, fans, and power supply with the measurements below.
Bykski’s motherboard layout. 1 is Mini-ITX, 2 is Micro-ATX, and 3 is ATX.
Design Highlights
Acrylic distro plate built into the frame
The clear plate runs around the motherboard opening. Its channels give you connection points for routing tubing between your loop components.
Bykski’s mounting diagram. Both green areas marked 6 are for radiators and fans. The blue area marked 7 is for the power supply.
Radiators and power supply mount behind the board
The frame has two 360 mm radiator positions above the ATX power supply mount. Check radiator thickness, fan thickness, and power supply length before you plan the rear layout.
Key Specifications
| Model | B-CEC-X |
|---|
| Color | Black |
|---|
| Frame material | 3 mm aluminum plate |
|---|
| Distribution plate | Integrated acrylic, 10 + 8 mm |
|---|
| Upright size (W × H × D) | 440 × 329 × 286 mm |
|---|
| Placement | Angled upright or flat |
|---|
| Radiator mounts | 2 × 360 mm |
|---|
| Radiator footprint shown | 395 × 124.5 mm |
|---|
| Max. radiator thickness | 31.6 mm |
|---|
| Fan mounts | Up to 6 × 120 mm fans |
|---|
| Max. fan thickness | 28 mm |
|---|
| ATX power supply length | Up to 220 mm |
|---|
| Reservoir mounting area | Fits a reservoir up to 300 mm long |
|---|
Bykski’s dimension drawing shows the frame in its angled upright position. Measurements are in millimeters.
Which Version Do I Need?
Choose the frame based on how you want to route your coolant.
Bykski B-CEC-XTHIS PAGE
Choose this model if you want the acrylic distribution plate built into the frame.
Choose this stand-alone aluminum frame if you plan to place and connect your own loop components.
What's in the Box
1 × chassis with integrated distro plate1 × accessory bag
Fan mounting screws are included.
Supply your own pump and the other components for your build.
Bykski’s accessory illustration shows a drive bracket, a 360 mm radiator bracket, and example mounting screws.
Installation & Use
1Choose upright or flat placement, then check the dimensions of your board, radiators, fans, and power supply.
2Fit the chassis supports, graphics card bracket, power supply bracket, and power button.
3Fit the radiator brackets, radiators, and fans, using the included mounting screws for the fans. Install the ATX power supply after the radiator and fan assemblies are in place.
4Connect the distro plate to your loop with tubing and matching fittings, following the instructions for your loop components.
5Fill the loop and power only the pump to check for leaks. Inspect the connections before powering the rest of the PC.
For the loop, prepare a separate pump, radiators, fans, water blocks for the components you want to cool, fittings, tubing, and coolant.
Bykski’s radiator and fan assembly diagram. 1 points to the lower position and 2 points to the upper position.
FAQ
Does the B-CEC-X come with a pump?
This SKU includes the chassis with its distribution plate and an accessory bag. Supply your own pump.
Can I mount two 360 mm radiators?
Yes. Bykski shows a 395 × 124.5 mm radiator footprint for each mount and specifies a 31.6 mm thickness limit. Compare those dimensions with the radiators you plan to use.
Can the B-CEC-X lie flat?
Yes. The frame is designed for either angled upright or flat placement.
Will my ATX power supply fit?
The chassis supports one ATX power supply up to 220 mm long. Install it after the radiator and fan assemblies.
Notes- This link only contains an aluminum chassis frame and a bag of accessories.
- "The renderings are for reference only. Please refer to the actual product for details.
- "If you have any other questions, please consult the seller.