Bykski · B-PMD3-X
DDC pump with PWM control and a clear acrylic top
The Bykski B-PMD3-X is a DDC pump that circulates coolant through a custom PC water cooling loop. Its preinstalled clear acrylic top has G1/4 inlet and outlet ports for connecting the pump to your plumbing. A 12 V Molex connection powers the pump, and a separate PWM lead lets you adjust its speed.
Use With
Match your fittings, reservoir, and power connections before ordering.
- ✓G1/4 fittings for the pump inlet and outlet
- ✓Bykski B-CT50-MBK 50 mm reservoir for direct mounting
- ✓4-pin peripheral Molex from the PC power supply, plus a separate 4-pin PWM control header
Design Highlights
Clear PMMA pump top
The acrylic top comes installed on the black pump housing. Choose G1/4 fittings that match the type and size of tubing in your loop.
1 and 2 are the power leads. 3 is RPM feedback. 4 is PWM speed control.
Separate power and PWM leads
The large 4-pin Molex plug draws power from the PC power supply. The smaller 4-pin plug carries the PWM signal and reports pump speed.
Key Specifications
| Model | B-PMD3-X |
|---|
| Pump type | DDC |
|---|
| Pump top | Clear PMMA acrylic |
|---|
| Housing | Black engineering plastic |
|---|
| Body dimensions | 62 × 62 × 53 mm |
|---|
| Inlet and outlet | G1/4 |
|---|
| Rated supply | 12 V DC |
|---|
| Power connector | 4-pin peripheral Molex |
|---|
| Control connector | 4-pin PWM with tachometer feedback |
|---|
| Drive and shaft | Sine-wave drive, ceramic shaft |
|---|
| Maximum head | 6 m |
|---|
Bykski’s pump body drawing. Dimensions are in millimeters.
Which Version Do I Need?
Bykski lists B-PMD3-X and B-PMD3-COV under separate model numbers. Check the full part number when replacing a PMD3 pump.
Bykski B-PMD3-XTHIS PAGE
Choose this pump with its preinstalled acrylic top when you’re supplying your own reservoir.
Choose this model if you want a pump with preinstalled aluminum armor.
Select a reservoir combo option on this listing to get the armored pump with a tube reservoir.
What's in the Box
Bykski B-PMD3-X pump with preinstalled acrylic top
Installation & Use
1Check case clearance for the pump, reservoir, and fittings. For a supported pump-and-reservoir mount, Bykski shows the B-BKT-105 bracket with clear reservoir clamps.
2Connect your reservoir to the pump inlet and plumb the loop with matching G1/4 fittings. For direct mounting with the B-CT50-MBK, remove the reservoir’s lower end cap before fitting it to the pump.
3Plug the large 4-pin Molex connector into the power supply. Connect the smaller lead to a 4-pin PWM header for speed control and RPM feedback.
4Fill the reservoir and prime the pump before applying power. Run only the pump while you top up the reservoir, bleed air, and check for leaks. Power the rest of the PC after the loop passes the leak test.
For a new loop, plan for a reservoir, compatible mounting hardware, G1/4 fittings, matching tubing, coolant, a radiator, and the water block or blocks for your hardware.
Bykski’s direct-mount reservoir setup.
FAQ
Do I need a separate DDC pump top?
The clear acrylic pump top comes preinstalled and has G1/4 inlet and outlet ports.
What powers the pump and what controls its speed?
A 4-pin peripheral Molex connector supplies 12 V DC from the PC power supply. The separate 4-pin PWM connector handles speed control and RPM feedback.
Which reservoir can I mount directly?
Bykski shows its 50 mm B-CT50-MBK tube reservoir mounting directly to the pump top.
Do I need special tubing for the G1/4 ports?
Use G1/4 fittings on the pump. Choose the fitting type and size to match the tubing in your loop.
Notes- During filling, stop the pump before the reservoir empties. Running the pump dry can damage it.