Universal Distro Plate for Radiator Mounts, Bykski RGV-DDC-X-TK120/240/360

Bykski · RGV-DDC-X-TK120/240/360

Universal distro plate for a PC radiator mount

The Bykski RGV-DDC-X-TK series is an acrylic distribution plate that routes coolant between components in a custom PC loop. It uses a matching radiator mount in the case, so plan a separate position for the loop’s radiator. Each size is available with a preinstalled DDC pump and heatsink cover or as a plate without a pump.

Fits
120 / 240 / 360 mm radiator mounts
Ports
G1/4
Lighting
5V 3-pin ARGB
Pump options
Preinstalled DDC or no pump

Compatibility

Match the plate to an available radiator mount in your case.

  • ✓RGV-DDC-X-TK120 for a 120 mm radiator mount
  • ✓RGV-DDC-X-TK240 for a 240 mm radiator mount
  • ✓RGV-DDC-X-TK360 for a 360 mm radiator mount

The plate occupies one radiator position. Before ordering, check the mounting holes and available clearance for the plate, pump, and fittings. Set aside a separate position for the radiator.

TK360 radiator-mount example.

Design Highlights

Acrylic channels with G1/4 ports

The machined acrylic channels bring the loop connections together at the plate. Choose G1/4 fittings that match the tubing you plan to use.

Bykski’s TK360 soft-tube build example.

Route hard or soft tubing

The plate supports both hard and soft tubing with matching fittings. Plan the runs from the plate to your blocks and radiator around the hardware in your case.

TK360 shown with the optional pump installed.

5V addressable lighting

Use the sync cable with a 5V 3-pin ARGB header on your motherboard or a compatible controller.

Key Specifications

TK120 plate (L × W × T)120.00 × 124.50 × 31.60 mm
TK240 plate (L × W × T)240.00 × 124.50 × 31.60 mm
TK360 plate (L × W × T)360.00 × 124.50 × 31.60 mm
ColorBlack
ConstructionCNC-machined acrylic with an aluminum mounting plate
TK360 acrylic layers8 mm upper cover, 10 mm lower cover
Coolant port threadsG1/4
Lighting connection5V 3-pin ARGB (RBW)
Pump optionsPreinstalled DDC with heatsink cover or no pump

Bykski’s TK360 drawing. Dimensions are for the plate body in millimeters.

Which Version Do I Need?

Choose the size by radiator mount first, then decide whether you want the pump installed.

Bykski RGV-DDC-X-TK seriesTHIS PAGE
Choose the preinstalled DDC option for an assembled plate and pump. Choose No pump if you’ve confirmed a compatible DDC pump for the plate.
Choose this 120, 240, or 360 mm radiator-mount alternative if you want a plate supplied with Barrow’s SPB-17 pump.

What's in the Box

1 × distro plate in the selected sizeMounting hardware5V ARGB LED stripARGB sync cablePreinstalled DDC pump with heatsink cover (pump option only)

Installation & Use

1
Test-fit the plate at the radiator mount and check the space for the pump and fittings.
2
If you selected No pump, confirm the exact DDC pump model with the seller before fitting it to the plate.
3
Fasten the plate at the radiator mount using the threaded mounting points in its rear aluminum plate.
4
Plan the tube runs to the radiator and water blocks. Install the G1/4 fittings, connect the tubing, and seal any unused coolant ports.
5
If you’re using the lighting, connect the sync cable to a 5V 3-pin ARGB header or compatible controller. Do not connect it to a 12V 4-pin RGB header.
6
Fill the loop with coolant and check for leaks before powering the PC hardware.

For a new loop, have a radiator, water blocks, tubing, matching G1/4 fittings, port plugs as needed, and coolant. The No pump option also requires a compatible pump.

Bykski’s TK360 example showing how the plate connects to a radiator and water blocks.

FAQ

What size universal distro plate should I choose?

Choose TK120, TK240, or TK360 for the matching 120, 240, or 360 mm radiator position. Check the mounting holes and compare the plate dimensions with the available space before ordering.

Does the distro plate come with a pump?

Each size can be ordered with a preinstalled DDC pump and heatsink cover or with no pump. Confirm the exact model if you plan to fit your own DDC pump.

Can I use soft tubing with the plate?

Yes. Use G1/4 fittings sized for your soft tubing. For hard tubing, select G1/4 fittings that match its outside diameter.

Which ARGB header do I use?

Connect the sync cable to a 5V 3-pin ARGB header. Do not connect it to a 12V 4-pin RGB header. If your motherboard lacks a 5V ARGB header, use a compatible controller that you supply.

Notes
  • Depending on the motherboard, blocks, fittings used, and layout, the connecting tubing may not appear as pictured (perfectly horizontal). Not responsible for any hardware damage. Use at your own risk.
  • All pumps, radiators, reservoirs, cases, fittings and other products in details photos are for reference only. The preinstalled DDC pump and heatsink cover are included when you select the pump option.
  • As Bykski upgrades or adjusts the contents of the kit from time to time, such as product updates version, model or appearance, adjustments to the layout, etc..
  • If not notified in time, the Bykski's latest real object shall prevail.