FormulaMod · Fm-BZXZ-EVGA

Sleeved replacement cables for modular PC power supplies

The FormulaMod Fm-BZXZ-EVGA is an individually sleeved cable kit designed to replace the cables on a fully modular EVGA desktop power supply. Three kit layouts give you different cable lengths and counts for routing inside your case. Check your exact power supply model and follow EVGA’s cable requirements before ordering.

PSU version
EVGA
Wire gauge
18 AWG
Connection
Direct to PSU
Kit options
A · A+ · B

Compatibility

Check the model and full part number on your EVGA PSU before ordering. If a hardware revision is needed to identify the correct cables, confirm it with EVGA.

Models covered by EVGA’s cable restrictions
EVGA’s manuals for the SuperNOVA models below specify original or model-specific EVGA cables. Those manuals do not list this FormulaMod kit as a supported replacement.

SuperNOVA G2
550 G2, 650 G2, 750 G2, 850 G2, 1000 G2, 1300 G2, 1600 G2

SuperNOVA G3
550 G3, 650 G3, 750 G3, 850 G3, 1000 G3

SuperNOVA G+
650 G+, 750 G+, 850 G+, 1000 G+, 1300 G+, 1600 G+, 2000 G+

BQ models incompatible with a full cable swap
500 BQ, 600 BQ, 650 BQ, 750 BQ, and 850 BQ have a hardwired motherboard power cable. For their removable leads, use the cables EVGA specifies in the manual for your model.

For other models, check the EVGA manual for your specific PSU before ordering. Matching plugs can have different wiring.

Design Highlights

Direct connection to the power supply

These cables connect the power supply to the motherboard, graphics card, drives, and other peripherals. Check the exact PSU model and the connector requirements of each device.

Individually braided wires

Each conductor has its own insulation and braided sleeve. The sleeved wire measures 3 mm across.

Series photo showing how cable combs hold the wires in rows.

Included cable combs

Use the included combs to keep wire strands aligned along visible runs. Check the cable lengths against your case’s routing path before choosing a kit.

Key Specifications

ModelFm-BZXZ-EVGA
Wire18 AWG conductor
3 mm sleeved wire diameter
ConstructionIndividually braided sleeves and insulated wires
ATX 24-pin motherboardA / A+ 1 × 650 mm
B 1 × 400 mm
EPS 4+4-pin CPUA / A+ 1 × 850 mm
B 1 × 650 mm
PCIe 6+2-pin GPUA 2 × 650 mm
A+ 3 × 650 mm
B 2 × 400 mm
SATA powerA / A+ 1 × 350 mm and 1 × 500 mm
B 1 × 400 mm and 1 shorter cable
Molex 4-pin peripheralA / A+ 1 × 350 mm and 1 × 400 mm
B 1 × 350 mm

The drawing shows the two plugs at the PSU end of the motherboard cable. Verify wiring and cable approval with the PSU manufacturer.

Which Version Do I Need?

Start with the brand and exact model on your PSU label. Each version has its own PSU-side connector layout.

Fm-BZXZ-EVGATHIS PAGE
EVGA version. Follow your EVGA model’s cable requirements in the Compatibility section.
Corsair version. Check the separate listing and Corsair’s requirements for your exact PSU model.
ASUS, Seasonic, and Antec version. Check the separate listing and the PSU manufacturer’s cable requirements for your exact model.

What's in the Box

Kit A · 8 cablesKit A+ · 9 cablesKit B · 7 cables

You receive the cables for the kit you select, in the lengths and quantities listed above.

Cable combs are included.

The power supply and SATA splitter are excluded.

Sleeve Colors

Orange

Red

White

Blue

Green

Black

Black x Green

Sky Blue

Silver

Gray

Purple

Pink

Black x Red

Installation & Use

1
Check your PSU model and full part number, then read the manual for that model. Use replacement cables only when the PSU manufacturer accepts them for that model.
2
Shut down the PC, switch off the PSU, and unplug the AC cord. Disconnect each cable you are replacing at both ends.
3
Connect each approved replacement to its matching PSU port and device. Use the ATX lead for the motherboard, EPS for CPU power, PCIe for graphics, and SATA or Molex for the appropriate peripherals.
4
Check that every plug is in the correct port and fully seated before reconnecting the AC cord and turning the PSU on.

Use a fully modular PSU with verified cable support. Check that the selected kit has enough leads of the right types and lengths for your components.

Series example of the SATA power plug that connects to the drive.

FAQ

Can I use this kit with an EVGA SuperNOVA G2, G3, or G+?

Use the original EVGA cables or EVGA cables approved for your exact model. The Compatibility section lists the models covered by those manual requirements.

Can I use this kit with an EVGA 600 BQ or 750 BQ?

This kit cannot replace the full cable set on either model because the motherboard power cable is hardwired. For removable leads, follow the EVGA manual for your exact model.

Do these cables plug straight into the PSU?

Yes. These are direct replacement leads. Check the PSU model and wiring requirements before connecting any replacement cable.

How do I choose between Kit A, A+, and B?

A and A+ have the same motherboard, EPS, and PCIe cable lengths. A+ adds a third PCIe lead. B has shorter motherboard, EPS, and PCIe leads.

How many CPU power cables come with each kit?

Each kit has one EPS 4+4-pin CPU cable. Check your motherboard’s CPU power requirements before choosing a kit.

Notes
  • The following shop policy refers to the model list on the original product page.
  • If they use in other PSUs that are out of the list and cause any damage, we are not responsible for this.