Description
The FormulaMod Fm-BZXZ-EVGA is an individually sleeved cable kit designed to replace the cables on a fully modular EVGA desktop power supply. Three kit layouts give you different cable lengths and counts for routing inside your case. Check your exact power supply model and follow EVGA’s cable requirements before ordering.
Check the model and full part number on your EVGA PSU before ordering. If a hardware revision is needed to identify the correct cables, confirm it with EVGA.
Models covered by EVGA’s cable restrictions
EVGA’s manuals for the SuperNOVA models below specify original or model-specific EVGA cables. Those manuals do not list this FormulaMod kit as a supported replacement.
SuperNOVA G2
550 G2, 650 G2, 750 G2, 850 G2, 1000 G2, 1300 G2, 1600 G2
SuperNOVA G3
550 G3, 650 G3, 750 G3, 850 G3, 1000 G3
SuperNOVA G+
650 G+, 750 G+, 850 G+, 1000 G+, 1300 G+, 1600 G+, 2000 G+
BQ models incompatible with a full cable swap
500 BQ, 600 BQ, 650 BQ, 750 BQ, and 850 BQ have a hardwired motherboard power cable. For their removable leads, use the cables EVGA specifies in the manual for your model.
For other models, check the EVGA manual for your specific PSU before ordering. Matching plugs can have different wiring.
These cables connect the power supply to the motherboard, graphics card, drives, and other peripherals. Check the exact PSU model and the connector requirements of each device.
Each conductor has its own insulation and braided sleeve. The sleeved wire measures 3 mm across.
Use the included combs to keep wire strands aligned along visible runs. Check the cable lengths against your case’s routing path before choosing a kit.
| Model | Fm-BZXZ-EVGA |
|---|---|
| Wire | 18 AWG conductor 3 mm sleeved wire diameter |
| Construction | Individually braided sleeves and insulated wires |
| ATX 24-pin motherboard | A / A+ 1 × 650 mm B 1 × 400 mm |
| EPS 4+4-pin CPU | A / A+ 1 × 850 mm B 1 × 650 mm |
| PCIe 6+2-pin GPU | A 2 × 650 mm A+ 3 × 650 mm B 2 × 400 mm |
| SATA power | A / A+ 1 × 350 mm and 1 × 500 mm B 1 × 400 mm and 1 shorter cable |
| Molex 4-pin peripheral | A / A+ 1 × 350 mm and 1 × 400 mm B 1 × 350 mm |
Start with the brand and exact model on your PSU label. Each version has its own PSU-side connector layout.
You receive the cables for the kit you select, in the lengths and quantities listed above.
Cable combs are included.
The power supply and SATA splitter are excluded.
Use a fully modular PSU with verified cable support. Check that the selected kit has enough leads of the right types and lengths for your components.
Use the original EVGA cables or EVGA cables approved for your exact model. The Compatibility section lists the models covered by those manual requirements.
This kit cannot replace the full cable set on either model because the motherboard power cable is hardwired. For removable leads, follow the EVGA manual for your exact model.
Yes. These are direct replacement leads. Check the PSU model and wiring requirements before connecting any replacement cable.
A and A+ have the same motherboard, EPS, and PCIe cable lengths. A+ adds a third PCIe lead. B has shorter motherboard, EPS, and PCIe leads.
Each kit has one EPS 4+4-pin CPU cable. Check your motherboard’s CPU power requirements before choosing a kit.