120 mm Fan Copper Radiator, 39 mm Thick – FormulaMod Fm-CoRa2H

FormulaMod · Fm-CoRa2H

39 mm copper and brass radiator for custom PC water cooling

The FormulaMod Fm-CoRa2H is a 39 mm-thick copper and brass radiator for custom desktop PC water cooling. It uses 120 mm fans to move air through the fins and carry heat away from the coolant. Both G1/4 ports sit at the same end, so you can route both tubes from that side.

Body thickness
39 mm
Fits
120 mm fans
Ports
2 × G1/4
Materials
Copper and brass

Fan and Case Fit

Choose the radiator size that matches your case mount. All four sizes use 120 mm fans.

  • ✓120 mm radiator mount · 1 fan position per side
  • ✓240 mm radiator mount · 2 fan positions per side
  • ✓360 mm radiator mount · 3 fan positions per side
  • ✓480 mm radiator mount · 4 fan positions per side

Before ordering, compare the actual body dimensions with your case clearance. Allow extra room for the fan thickness, fittings, and tubing.

480 mm at top, 360 mm in the middle, 240 mm at lower left, and 120 mm at lower right.

Design Highlights

Finned heat exchanger

The radiator carries coolant through 14 channels while the fans move air across the fin stack.

Two ports at one end

Connect both tubes with G1/4 fittings and leave room at the port end for the fittings and tubing.

Key Specifications

ModelFormulaMod Fm-CoRa2H
MaterialsCopper and brass
ColorBlack
Coolant ports2 × G1/4, at one end
Mounting threadM3
Coolant channels14
Pressure test value1.5 bar
SKUBody size (L × W × T)
Fm-CoRa2H-120154 × 122 × 39 mm
Fm-CoRa2H-240276 × 122 × 39 mm
Fm-CoRa2H-360396 × 122 × 39 mm
Fm-CoRa2H-480516 × 122 × 39 mm

Fm-CoRa2H-240 shown. The table lists the overall body dimensions for each size.

Which Version Do I Need?

Compare the two body thicknesses after checking the space available for the radiator and fans.

Fm-CoRa2H · 39 mmTHIS PAGE
Choose this version if the mount has room for a 39 mm radiator body plus the fans, fittings, and tubing.
Choose the thinner version when space is tight. It has the same body length and width in each corresponding size.

What's in the Box

1 × Fm-CoRa2H radiator in the selected sizeFan mounting screws

Installation & Use

1
Test-fit the radiator and fans at the case mount. Check the space at the port end before routing the tubing.
2
Mount the fans and radiator with M3 screws sized for the mounting stack. Use the included fan mounting screws if they are the right length. For a 25 mm-thick fan, FormulaMod shows an M3 × 30 mm screw. Check the length again if you use a thinner fan or a different mounting arrangement. Limit screw penetration into the fin side to 5 mm.
3
Fit the G1/4 fittings, connect the tubing, and fill the loop with coolant.
4
Check the loop for leaks before powering the rest of the PC.

A complete loop uses 120 mm fans, G1/4 fittings, tubing, a pump, a reservoir, a water block, and coolant.

Product Gallery

FAQ

How thick is the Fm-CoRa2H?

The radiator body is 39 mm thick in all four sizes. Measure for your fan thickness as well.

Does the 120 size measure 120 mm long?

The Fm-CoRa2H-120 body measures 154 × 122 × 39 mm. The 120 size corresponds to one 120 mm fan position per side.

What fittings does it take?

Both coolant ports use G1/4 threads and are located at the same end.

How far can the mounting screws go into the radiator?

FormulaMod limits penetration on the fin side to 5 mm. Choose a screw length that accounts for the fan and any material between the screw head and radiator.

Notes
  • Check screw length whenever you change fans or brackets. A screw that reaches too far can damage the radiator and cause a leak.